Brake system of car Mitsubishi Galant 5

Brake system — specification
General information Brake fluid type - See Chapter 1 Clearance between the brake booster pushrod and the master cylinder piston Precis (up to and including 1989) - from...

Brake system — general description
The vehicles described in this manual are equipped with front and rear hydraulic brake systems. The front brakes are disc brakes, while the rear brakes may be either...

Anti-lock braking system (ABS) — general description
The anti-lock braking system (ABS) is designed to ensure vehicle control, stability and optimal braking under various braking conditions and on any road surfaces. The...

Disc brake pads (front and rear) — replacement
Warning: Replacement of disc brake pads must be performed on both front or rear wheels at the same time: never replace pads on only one wheel. In addition, dust...

Disc brake mechanism — removal, overhaul and installation
Warning: Dust generated in the brake system may contain asbestos. Never blow off dust with compressed air. Wear a cloth mask when working on the brakes. Do not use...

Brake disc — inspection, removal and installation
1. Loosen the wheel nuts, jack up the car and place it on supports. Remove the wheel. 2. Remove the brake mechanism, pads and caliper as described in section 4 . It is...

Drum brake shoes — replacement
Warning: Replacement of drum brake shoes must be performed on both wheels at the same time; never replace the brake pads on just one wheel. In addition, the dust...

Wheel brake cylinder — removal, overhaul and installation
Note: If you decide to overhaul the brake cylinders yourself, purchase a repair kit. Overhaul both brake cylinders at once - overhauling one of them is not allowed...

Master Brake Cylinder — Removal, Overhaul and Installation
Note: If your vehicle is equipped with anti-lock braking system (ABS), have it overhauled by your dealer. Removal 1. The brake master cylinder is located in the engine...

Brake force regulator — removal and installation
Removal 1. Although special equipment is required to diagnose faults in the brake force regulator, it can be removed and replaced at home. 2. The pressure limiter is...

Brake Hoses and Tubes — Inspection and Replacement
1. Every six months, it is necessary to inspect the brake rubber hoses connecting the steel pipes to the front and rear brake mechanisms for cracks, wear of the outer...

Hydraulic brake system — bleeding
Warning: Wear safety glasses when bleeding the system. If brake fluid gets into your eyes, rinse your eyes with water immediately and consult a doctor. Note: Bleeding...

Brake booster — inspection, removal and installation
Checking the work 1. With the engine off, press the brake pedal several times. Make sure that the pedal travel does not change. 2. Press the pedal and start the engine....

Parking brake — adjustment
1. Pull the parking brake lever up as far as it will go, counting the clicks as you pull the lever. The lever should move five to seven clicks. If the lever can be...

Parking Brake Cables — Replacement
Note: This procedure applies to both left and right cables. 1. Remove the center panel ( see Chapter 11 ). On some models it may be necessary to remove the floor panel...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Similar materials for other Mitsubishi models

➤ Chassis and running gear: Brake system Mitsubishi Colt 5 (1995-2003, petrol)
➤ Chassis and running gear: Brake system Mitsubishi Lancer 9 (2000-2007, petrol)
➤ Chassis and running gear: Brake system Mitsubishi L200 4 (2005-2014, diesel)
➤ Chassis and running gear: Brake system Mitsubishi Outlander 1 (2003-2008)
➤ Chassis and running gear: Brake system Mitsubishi Pajero 4 (2006-2021)
➤ Chassis and running gear: Brake system Mitsubishi Space Star (1998-2005)

Share with friends:

Link in different formats to this section

TEXTHTMLBB Code