Front and rear suspension of car Mitsubishi Galant 5

Suspension and steering — specification
Tightening torques Nm Front suspension Upper nuts for mounting the front strut Preds - from 15 to 19 Galant — from 40 to 49 Mirage — from 34 to 45 Cordia/Tredia — from...

Suspension and steering — general description
The front suspension is designed on the basis of the MacPherson strut. The steering knuckle is moved by the lower suspension arm. The anti-roll bar, mounted on the front...

Front Anti-Roll Bar — Removal and Installation
Removal 1. Jack up the front of the vehicle and place it on supports. Apply the parking brake and block the rear wheels. 2. Remove the exhaust pipe ( see Chapter 4 ). 3....

Stretching — removal and installation
Note: Some models do not have a strut brace. Removal 1. Jack up the front of the car and place it on supports. Apply the parking brake and block the rear wheels. Remove...

Front Strut/Shock Absorber and Coil Spring — Removal, Inspection and Installation
Removal 1. Loosen the wheel nuts, raise the front of the car and place it on supports. Apply the parking brake and block the rear wheels. Remove the front wheel. 2....

Shock absorber — replacement
Caution: Removing the shock absorber from the coil spring assembly on vehicles equipped with Electronic Controlled Suspension (ECS) requires a special expensive tool to...

Lower control arm — removal, inspection and installation
Removal 1. On the side you have chosen to work on, loosen the wheel nuts, raise the front of the vehicle, place it on supports, then apply the parking brake and block...

Ball joints — inspection and replacement
Examination 1. Raise the vehicle and support it on supports. 2. Inspect the rubber boots for cuts, tears, or grease leaks. If such damage occurs, replace the ball...

Steering knuckle and hub — removal and installation
Warning: Dust generated in the brake system may contain asbestos, which is harmful to your health. Never blow off dust with compressed air or inhale it. Wear a cloth...

Front Hub and Bearing — Removal and Installation
Pressing the hub and bearing out of the steering knuckle requires special equipment and skills, so this work should be entrusted to a professional auto mechanic....

Rear Anti-Roll Bar (Precis Model Only) — Removal and Installation
1. Remove the rear axle beam as described in section 14 . 2. Use a marker or scratches to make alignment marks on the stabilizer, aligning them with the marks stamped on...

Cross tie rod — removal and installation
1. Raise the rear of the vehicle and support it on stands. 2. Unscrew the nut on the left end of the transverse rod, as well as the bolt and nut on the right end of the...

Rear Coil Spring — Removal, Inspection and Installation
Application: Precis models are equipped with shock absorbers and separate springs; on all other models, the shock absorber and spring are connected into one unit....

Rear shock absorber — removal and installation
1. Loosen the rear wheel nuts, raise the rear of the vehicle and place it on stands. Block the front wheels. Remove the rear wheel(s). 2. Place a jack under the rear...

Rear axle beam — removal, overhaul and installation
Removal 1. Loosen the nuts securing both rear wheels, lift the rear of the vehicle and place it on supports. The supports should be installed directly under the support...

Wheels and tires — general information
All vehicles described in this manual are equipped with metric size fiberglass or steel radial tires (see illustration). Using other sizes and types of tires may result...

Front Wheel Alignment Angles — General Information
Front wheel alignment means changing the position of the front wheels in relation to the suspension and the ground. Correct front wheel alignment not only improves...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Similar materials for other Mitsubishi models

➤ Chassis and running gear: Car suspension Mitsubishi Colt 5 (1995-2003, petrol)
➤ Chassis and running gear: Car suspension Mitsubishi L200 4 (2005-2014, diesel)
➤ Chassis and running gear: Suspension and drive shafts Mitsubishi Space Star (1998-2005)

Share with friends:

Link in different formats to this section

TEXTHTMLBB Code