Eengine electrical equipment of car Mitsubishi Galant 5

Engine Electrical System — Specification
Distributor Sensor Air Gap Note: Air gap checking and adjustment is only performed on the models listed below Cordia and Tredia. 1983 - from 0.2 to 0.38 mm 1984 and 1985...

Engine Electrical System — General Description
Engine electrical equipment includes components of the ignition, battery charging, and starting systems. Because these systems serve the engine, they are considered...

Battery — Removal and Installation
1. Warning: Always disconnect the negative cable first and connect it last, otherwise a short circuit may occur when using a tool to loosen the wire clamps. Disconnect...

Battery Cables — Checking and Replacing
1. Periodically inspect the battery cables along their entire length for deformation, cracks, or burnt insulation or corrosion. Loose battery cable connections can cause...

Ignition system — general description and safety precautions
When working with the ignition system, take the following precautions: a) Do not hold the ignition key for more than 10 seconds if the engine does not start. b) Connect...

Ignition system — check
Warning: Extreme caution must be exercised when performing this test due to high voltages in the ignition system. 1. If the engine cranks over but does not start,...

Ignition Coil — Checking and Replacing
Examination Distributorless Healing System (DIS) Primary winding (1989) 1. Disconnect the primary winding wire connector. 2. Using an ohmmeter, measure the resistance...

Distributor — removal and installation
Removal 1. Disconnect the negative battery cable. 2. Disconnect the high tension wire from the distributor cap. 3. Disconnect the vacuum hose(s) from the vacuum advance...

Vacuum ignition timing regulator — checking and replacement
Examination 1. Disconnect the vacuum line from the vacuum advance regulator and plug it. If there are two lines, disconnect and plug the outer one (the one further from...

Sensor-switch — replacement
1. See detailed views ( illustrations 12.7a, 12.7b, 12.7c and 12.7d ). 2. When installing the switch, do not wipe off the conductive grease from it. 3. Before installing...

Checking and replacing the sensor coil
Note: This procedure only applies to the models described below. Cordia/Tredia 1.8L Turbo (1984 and 1985): Mirage 1.6L (1985) 1. Remove the distributor cap. 2. Remove...

Centrifugal ignition timing regulator — checking and replacing components
1. Disconnect the vacuum lines from the vacuum advance regulator on the distributor. 2. Attach the strobe light according to the manufacturer's instructions 3. Start the...

Distributor Sensor Air Gap — Checking and Adjusting
Note: This procedure applies to Cordia and Tredla 2.0L (1983 to 1988). Galant (all models). Mirage 1.5L (1985 to 1988) and Precis (1987 to 1989). 1. After each violation...

Battery Charging System — General Description and Safety Precautions
The charging system includes an alternator with a built-in voltage regulator, a charge indicator, a battery, a fusible link and connecting wires. The charging system...

Charging system — check
1. If a fault has occurred in the charging system circuit, perform the following check before performing the alternator test: a) Check the tension of the drive belt and...

Generator — removal and installation
Cordia, Precis and Tredia 1. Remove the power steering oil pump and alternator drive belts ( see Chapter 1 ). 2. Remove the power steering pump (see illustration). 16.2....

Voltage Regulator/Generator Brushes — Replacement
Precis 1988 (Bosch type) Note: If you decide to replace the brushes (but not the entire regulator), you will need to desolder the old brushes from the regulator and...

Launch system — general description and safety precautions
The primary function of the starting system is to crank the engine fast enough to start it. The starting system consists of a battery, a starter, a starter traction...

Starter — Checking in a Car
Note: Before troubleshooting the starter, make sure the battery is fully charged. 1. If the starter does not engage at all when the ignition is turned on, make sure the...

Starter — removal and installation
1. Disconnect the negative battery cable. 2. Disconnect the electrical connectors from the starter/starter solenoid assembly. 3. Unscrew the starter mounting bolts (see...

Starter Solenoid Relay — Removal and Installation
1. Disconnect the negative battery cable. 2. Remove the starter ( see section 19 ). 3. Disconnect the large starter wire from the solenoid terminal. 4. Unscrew the...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Similar materials for other Mitsubishi models

➤ Gasoline engines: Engine electrical equipment Mitsubishi Colt 5 (1995-2003, petrol)
➤ Power unit: Engine electrical equipment Mitsubishi Pajero 4 (2006-2021)
➤ Power unit: Engine electrical equipment Mitsubishi Carisma (1995-2004)

Share with friends:

Link in different formats to this section

TEXTHTMLBB Code