Engine repair of car Mitsubishi Galant 5

Engine — Specifications
General information The order of work is 1-3-4-2 Cylinder numbering on the drive belt side is 1-2-3-4 1.5L engine Camshaft Axial clearance of the camshaft - from 0.05 to...

General information and engine identification
This part Chapters 2 is dedicated to engine repair without removing it from the vehicle. Information regarding engine removal and installation and overhaul of the...

Repair procedures that can be performed without removing the engine from the vehicle
Most major repairs can be performed without removing the engine from the vehicle. First, clean the engine bay and the outside of the engine with an oil-based deposit...

Valve Cover — Removal and Installation
1. Disconnect the cable from the negative battery terminal. 2. Remove the air filter ( see Chapter 4 ). 3. Disconnect the high-voltage wires from the spark plugs and the...

Valve Rocker Arms — Removal, Inspection and Installation
Removal 1. Remove the valve cover ( see section 3 ). 2.. Set the piston of the first cylinder to the top dead center ( see Chapter 2B ) 3 Loosen the rocker shaft...

Valve springs, holders and valve stem seals — replacement
Note: Broken valve springs and damaged valve stem seals can be replaced without removing the cylinder head. This operation usually requires two special tools and a...

Hydraulic valve regulators — removal, inspection and installation
Note: Since hydraulic valve adjusters are precision parts, dust and other foreign particles must not be allowed to enter. Do not attempt to disassemble the hydraulic...

Toothed belt and sprockets
Caution: Do not attempt to rotate the crankshaft by the camshaft sprocket bolt or rotate the crankshaft counterclockwise. Also, do not rotate the crankshaft after...

Front Crankshaft Seal — Replacement
1. Remove the timing belt and crankshaft sprocket ( see section 7 ). 2. Wrap the end of a small screwdriver with electrical tape. Working under the left inner apron,...

Camshaft(s) — Removal, Inspection and Installation
Removal 1. Set the piston of the first cylinder to TDC ( see Chapter 2B ). 2. Disconnect the cable from the negative battery terminal. 3. Remove the valve cover ( see...

Intake manifold — removal and installation
1. Release pressure from the fuel system ( see Chapter 4 ), then disconnect the cable from the negative battery terminal. 2. Drain the cooling system ( see Chapter 1 )....

Exhaust manifold — removal and installation
Warning: Allow the engine to cool completely before starting the procedure. Removal 1. Disconnect the negative battery cable. On 16-valve Galant SOHC non-turbo models,...

Cylinder head — removal and installation
Caution: Allow the engine to cool completely before performing this procedure. Removal 1. Set the piston of the first cylinder to the TDC position ( see Chapter 2B ). 2....

Oil pan — removal and installation
Removal 1. Disconnect the cable from the negative battery terminal. 2. Raise the vehicle and place it on stable stands. 3. Remove the splash shield installed under the...

Oil pan — removal, inspection and installation
Note: Three different types of oil pumps are used on the various engines discussed in this manual. The 1.5L engine uses a gear-type unit driven by the crankshaft. The...

Flywheel/Drive Disc — Removal and Installation
Removal 1. Raise the vehicle and support it on stable stands, then remove the transmission as described in Chapter 7 . After this, you can replace the front gearbox seal...

Rear Main Seal — Replacement
1. For this operation it is necessary to remove the gearbox from the vehicle ( see Chapter 7 ). 2. The seal can be replaced without removing the oil pan and seal cover....

Engine Mounts — Checking and Replacing
1. Engine mounts generally rarely require attention, but broken or worn mounts should be replaced immediately, otherwise the additional load that will be transferred to...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Similar materials for other Mitsubishi models

➤ Power unit: Engine in a car Mitsubishi Colt 4 and 5 (1991-2003)
➤ Power unit: Engine repair Mitsubishi Lancer 3 and 5 (1984-1992)
➤ Power unit: Engine repair Mitsubishi Outlander 1 (2003-2008)
➤ Power unit: Engine repair Mitsubishi Pajero 4 (2006-2021)

Share with friends:

Link in different formats to this section

TEXTHTMLBB Code