Fuel and exhaust system of car Mitsubishi Galant 5

Fuel and exhaust system — specification
The resistance of the air damper heater is 6 Ohms at room temperature Engine speed for damper adjustment is 1800 rpm Resistance of the electromagnetic valve Float...

Fuel and exhaust system — general information
Note: Determine the type of fuel system installed on your vehicle (carburetor with or without FBC or with TBI/MPI fuel injection) using the table below. Carburetor The...

Bleeding Fuel Pressure (Fuel Injected Models)
1. Locate the fuel pump electrical connector - if necessary see section 5 (some models have access from the trunk or from under the rear seat) 2. Remove the fuel tank...

Fuel Pump/Fuel Pressure — Check
Fuel pump - check Carburetor models 1. If you suspect insufficient fuel supply, first check all fuel lines to ensure that the problem is not due to a leak. 2. If the...

Fuel lines and fittings — general information
Examination 1. Sometimes you have to lift the car to service or replace some components (exhaust pipe suspension units, for example). Every time you work under the car,...

Fuel pump — removal and installation
Mechanical pump (carburetor models) 1. Disconnect the cable from the negative battery terminal. 2. Remove the fuel tank filler cap and release the pressure from the...

Fuel tank — removal and installation
Note: The following procedures are much easier to perform if the fuel tank is empty. Some tanks have a drain plug. If there is no drain plug, plan to remove the fuel...

Fuel tank — flushing and repair
1. Repairs to the fuel tank or filler neck must be performed by a specialist who has sufficient experience in performing such responsible and potentially dangerous work....

Air filter — removal and installation
1. Remove the air filter cover and filter element ( see Chapter 1 ). On later models with MPI, remove the battery, intake hoses and air flow sensor. Note: Always check...

Carburetor — removal and installation
Removal 1. Remove the fuel tank filler cap to relieve pressure in the tank. 2. Remove the air filter ( see section 8 ). 3. Disconnect the cable from the throttle lever (...

Carburetor — diagnostics and overhaul
Diagnostics 1. Before a thorough overhaul of the carburetor, it is necessary to conduct a full road test and check the adjustments. The values of some adjustments are...

Carburetor — checking on the car and adjustment
Note: If your vehicle is hard to start or does not start at all, idles poorly, or drivability is poor and you suspect a carburetor problem, it is best to first take your...

Fuel injection system
Note: The following procedure assumes that the fuel pump is working properly and the fuel pressure is correct ( see section 3 ). 1. Check all wiring connectors related...

Fuel injection unit (TBI) — removal, overhaul and installation
Removal 1. Release the pressure in the system ( see section 2 ). 2. Disconnect the cable from the negative battery terminal. 3. Drain the coolant to the intake manifold...

Fuel filter — general information
The models covered in this manual are equipped with two fuel filters, one in the fuel tank and one in the fuel line (fuel injected models) or in the engine compartment...

Multi-Point Injection (MPI) — Removal and Installation
Throttle body 1. Remove the throttle return spring and disconnect the throttle cable from the throttle body ( see section 16 ). 2. Tag and disconnect all wires and hoses...

Throttle Cable — Removal, Installation and Adjustment
Models without cruise control Cordie, Tredia, Mirage (except MPI) and Precis (except MPI) 1. On carbureted models, remove the air filter ( see section 8 ). 2. On all...

Exhaust System Maintenance — General Information
Warning: Checking and repairing exhaust system components should be done after the engine has been turned off, sufficient time for the system to cool completely. In...

Turbocharger — General Information
1. A turbocharger is used to increase power. When there is a need for more power and the throttle valve is open, the turbocharger forces more fuel-air mixture into the...

Turbocharger — Check
Caution: Operating the turbocharger with the ducts and filters disconnected may result in personal injury or damage to the impeller blades by foreign objects. Note: The...

Turbocharger — removal and installation
1. Remove the heat insulators ( see illustration 18.2 ). 2. Disconnect the oil return pipe from the oil pan. 3. Disconnect the oil feed pipe from the turbocharger and...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Similar materials for other Mitsubishi models

➤ Power unit: Fuel system (diesel) Mitsubishi Colt 4 and 5 (1991-2003)
➤ Power unit: Fuel system Mitsubishi Lancer 3 and 5 (1984-1992)
➤ Power unit: Fuel system Mitsubishi L200 4 (2005-2014, diesel)
➤ Power unit: Fuel system (gasoline) Mitsubishi Pajero 1 and 2 (1982-1999)
➤ Power unit: Diesel supply system F9Q1 Mitsubishi Space Star (1998-2005)

Share with friends:

Link in different formats to this section

TEXTHTMLBB Code