Exterior (external elements) of the car Mitsubishi L200 4

The Mitsubishi L200 car has three body modifications:

SINGLE CAB - a two-door cab equipped with only one row of seats;

CLUB CAB - also two-door, but equipped with an additional row of low comfort seats;

DOUBLE CAB - a four-door car with a full row of rear seats.

Elements of the vehicle cabin in the SINGLE CAB modification
1. Front crossmember; 2. Oil radiator bracket; 3. Oil cooler oil line bracket; 4. Front cross tube; 5. Radiator bracket; 6. Headlight side bracket; 7. Upper part of the...

Elements of the cargo compartment of the car in the SINGLE CAB modification
1. Front wall of the cargo compartment; 2. Inner panel of the cargo compartment side; 3. Internal side extension; 4. Rear light bracket; 5. Tailgate panel; 6. External...

Frame elements of the car in the SINGLE CAB modification
1. Cross beam of frame No.1; 2. Front cross beam of front wheel suspension; 3. Rear cross beam of the front wheel suspension; 4. Bracket of the rear cross beam of the...

Elements of the car cabin in the CLUB CAB modification
1. Front crossmember; 2. Oil radiator bracket; 3. Oil pipe bracket of oil radiator; 4. Front cross tube; 5. Radiator bracket; 6. Headlight side bracket; 7. Upper part of...

Elements of the cargo compartment of the car in the CLUB CAB modification
1. Front side panel; 2. Front side panel reinforcement; 3. Front wall of the cargo compartment; 4. Inner panel of the cargo compartment side; 5. Internal side extension;...

Elements of the car frame in the CLUB CAB modification
1. Cross beam of frame No.1; 2. Front cross beam of front wheel suspension; 3. Rear cross beam of the front wheel suspension; 4. Bracket of the rear cross beam of the...

Elements of the vehicle cabin in the DOUBLE CAB modification
1. Front crossmember; 2. Oil radiator bracket; 3. Oil cooler oil line bracket; 4. Front cross tube; 5. Radiator bracket; 6. Headlight side bracket; 7. Upper part of the...

Elements of the cargo compartment of the vehicle in the DOUBLE CAB modification
1. Front wall of the cargo compartment; 2. Front panel of the cargo compartment side; 3. Inner panel of the cargo compartment side; 4. Internal side extension; 5. Rear...

Frame elements of the car in the DOUBLE CAB modification
1. Cross beam of frame No.1; 2. Front cross beam of front wheel suspension; 3. Rear cross beam of the front wheel suspension; 4. Bracket of the rear cross beam of the...

Images of sections of cabin elements of the DOUBLE CAB modification
А 1. Roof panel; 2. Bracket for mounting the lamp in the passenger compartment; 3. Front roof beam В 1. Drainage gutter; 2. Upper inner dashboard panel; 3. Front wall of...

Images of sections of the cargo compartment elements of the DOUBLE CAB modification
м 1. Inner panel of the cargo compartment side; 2. Outer side panel; 3. Front side panel; 4. Filler neck bracket; 5. Front side reinforcement N 1. External cross panel...

Cabin and cargo compartment mounting diagram
1. Cabin mounting nut; 2. Washer; 3. Pillow; 4. Cushion bushing; 5. Buffer; 6. Washer; 7. Cabin mounting bolt; 8. Cargo compartment mounting nut; 9. Cargo compartment...

Adjusting the hood
To adjust the hood horizontally, loosen the bolt and nut (arrows) and move the lower part of the hinge in the directions shown. To adjust the height of the hood relative...

Radiator grille — removal and installation
The radiator grille is secured with latches and pins. The arrows in the figure indicate the locations of the latches.

Front bumper components installation diagram and its fastening
The figure shows the assembly diagram of the front bumper and the locations of the fastening elements. The arrows in the figure indicate the locations of the latches. 1....

Rear bumper components installation diagram and its fastening
1. Rear fog light connector (cars with fog lights); 2. Rear bumper and footrest assembly; 3. Rear bumper reinforcement; 4. Mounting plates

Engine protective sump
1. Front section of the pallet; 2. Rear section of the pallet

Removal and installation the front wing
Before removing the front fender, remove the turn signal repeater.

Filler cap mounting diagram
To adjust the position of the hatch, loosen the screws indicated by the arrows and set the position of the hatch. 1. Hatch; 2. Fixing clamp; 3. Damper; 4. Opening...

Side stand mounts
1. Footrest support; 2. Overlay; 3. End plate; 4. Footrest plate; 5. Bolt; 6. Nut; 7. Screw

Schematic diagram of the front headlights
1. Headlight level controller; 2. Headlight rear cover; 3. Lamp; 4. Side light bulb socket; 5. Parking light bulb; 6. Direction indicator lamp socket; 7. Direction...

Adjusting the front headlights
Before adjustment, the following conditions must be met. If the fuel tank is not filled, load the rear of the vehicle to 90% of the fuel tank (load at the rate of 1 l =...

Front fog light
1. Fog lamp glass trim; 2. Latch; 3. Fog lamp assembly; 4. Lamp; 5. Fog lamp housing; 6. Fog lamp bracket

Rear light
1. Rear light assembly; 2. Lamp holder; 3. Nest; 4. Direction indicator lamp; 5. Parking light and brake light lamp; 6. Spare lamp; 7. Rubber bushing; 8. Rubber bushing;...

Rear fog lamp
1. Rear fog light assembly; 2. Protective glass of the lantern; 3. Seal; 4. Lamp; 5. Flashlight body; 6. Nest; 7. Lamp; 8. Flashlight bracket; 9. Assembled flashlight...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Similar materials for other Mitsubishi models

➤ Body: Exterior (external elements) Mitsubishi Colt 5 (1995-2003, petrol)
➤ Body and interior: Exterior (external elements) Mitsubishi Lancer 3 and 5 (1984-1992)
➤ Body and interior: Exterior (external elements) Mitsubishi Galant 6 and 7 (1987-1998)
➤ Body and interior: Exterior (external elements) Mitsubishi Outlander 1 (2003-2008)
➤ Body and interior: Exterior (external elements) Mitsubishi Pajero 1 and 2 (1982-1999)
➤ Body and interior: Exterior (external elements) Mitsubishi Carisma (1995-2004)

Share with friends:

Link in different formats to this section

TEXTHTMLBB Code