Share with friends:
Car interior heating system Mitsubishi Lancer 3 and 5
Heater — general information
Fresh air for the heater is sucked in through the grille under the windshield and enters the passenger compartment through the heater ventilation system. The air flows...
Fresh air for the heater is sucked in through the grille under the windshield and enters the passenger compartment through the heater ventilation system. The air flows...
Heater Fan / Heater Unit
Cars produced since 9.88 1 - Fan 2 - Fan rotor 3 - Gasket ring 4 - Fan motor 5 - Resistance 6 - Heater housing 7 - Air ducts
Cars produced since 9.88 1 - Fan 2 - Fan rotor 3 - Gasket ring 4 - Fan motor 5 - Resistance 6 - Heater housing 7 - Air ducts
Checking/removing and installing the fan/ballast resistors (vehicles manufactured before 8.88)
Note: If the fan does not work at only one speed, the ballast resistor is usually defective. To replace the resistor, you need to remove the fan. Removal Disconnect the...
Note: If the fan does not work at only one speed, the ballast resistor is usually defective. To replace the resistor, you need to remove the fan. Removal Disconnect the...
Checking/removing and installing the fan/ballast resistors (vehicles produced since 9.88)
Note: If the fan does not work at only one speed, the ballast resistor is usually faulty. To replace the resistor, you need to remove the fan. Replacing the resistance...
Note: If the fan does not work at only one speed, the ballast resistor is usually faulty. To replace the resistor, you need to remove the fan. Replacing the resistance...
Removal and installation/adjustment of heater rods
Control rods and cables are replaced if the control levers move heavily and unevenly. Removal Remove the heater control panel frame from the instrument panel, see item....
Control rods and cables are replaced if the control levers move heavily and unevenly. Removal Remove the heater control panel frame from the instrument panel, see item....
Removal and installation air outlet nozzles
Removal The air outlet nozzles snap into the instrument panel and are removed with a wide screwdriver. For some nozzles, the instrument cluster must be removed to allow...
Removal The air outlet nozzles snap into the instrument panel and are removed with a wide screwdriver. For some nozzles, the instrument cluster must be removed to allow...
This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Similar materials for other Mitsubishi models
➤ Electrical equipment: Heating and air conditioning Mitsubishi Colt 4 and 5 (1991-2003)
➤ Body and interior: Heating and air conditioning Mitsubishi Space Star (1998-2005)
Link in different formats to this section
TEXTHTMLBB Code
- General information
- User manual
- Maintenance
- Power unit
- Repair of MPI engines
- Repair of GDI engines
- Engine overhaul
- Cooling and lubrication system
- MPI fuel injection system
- GDI fuel injection system
- Intake and exhaust system
- Starting and charging system
- Transmission
- Automatic gearbox
- Variator (CVT)
- Drive shafts and gearbox
- Chassis and running gear
- Front suspension
- Rear suspension
- Steering
- Brake system
- Body and interior
- Doors, locks and windows
- Exterior (external elements)
- Interior (internal elements)
- Electrical equipment
- Heater and air conditioner
- Security system SRS
- Equipment and devices
- Wiring diagrams (saloon)
- Wiring diagrams (wagon)
- General information
- Maintenance
- Power unit
- Engine repair
- Lubrication system
- Cooling system
- Ignition system
- Fuel system
- Carburetor
- Fuel injection
- Diesel power system
- Exhaust system
- Transmission
- Clutch
- Car gearbox
- Chassis and running gear
- Front suspension
- Rear suspension
- Steering
- Brake system
- Wheels and tires
- Body and interior
- Exterior (external elements)
- Interior (internal elements)
- Heating system
- Electrical equipment
- Equipment and devices
- Power devices
- Electrical circuits