Share with friends:
GDI fuel injection system Mitsubishi Lancer 9
General information about GDI engines
GDI Engine Design The main differences in the design of a GDI engine from a multipoint injection (MPI) engine. 1. Higher compression ratio (about 11-12). 2. Intake...
GDI Engine Design The main differences in the design of a GDI engine from a multipoint injection (MPI) engine. 1. Higher compression ratio (about 11-12). 2. Intake...
Periodic maintenance
Checking the position of the factory adjustment screw Do not touch the factory adjustment screw "Fixed SAS" on the throttle body, the position of which is adjusted with...
Checking the position of the factory adjustment screw Do not touch the factory adjustment screw "Fixed SAS" on the throttle body, the position of which is adjusted with...
Fuel injection system diagnostics
Note: The procedure for reading diagnostic trouble codes using a tester and the procedure for diagnosing a vehicle are given in the corresponding section of the chapter...
Note: The procedure for reading diagnostic trouble codes using a tester and the procedure for diagnosing a vehicle are given in the corresponding section of the chapter...
Checking the components of the GDI fuel injection system
Note: The procedures for checking the EGR servo and the canister purge solenoid valve are given in the relevant section of the chapter " Emission Control System "....
Note: The procedures for checking the EGR servo and the canister purge solenoid valve are given in the relevant section of the chapter " Emission Control System "....
Checking Fuel Injection System Components with an Oscilloscope
Mass Air Flow Sensor 1. Connect the oscilloscope (motor tester) sensor to terminal "3" of the mass air flow sensor connector or to the corresponding terminal of the...
Mass Air Flow Sensor 1. Connect the oscilloscope (motor tester) sensor to terminal "3" of the mass air flow sensor connector or to the corresponding terminal of the...
Removal and installation of GDI fuel injection system components
Removal and installation of fuel injection pump − Before you begin removing parts, perform the following operations: a) Remove the engine cover. b) Release residual...
Removal and installation of fuel injection pump − Before you begin removing parts, perform the following operations: a) Remove the engine cover. b) Release residual...
Electronic engine control unit
Removal and installation − Before you begin removing parts, perform the following operations: a) Remove the glove box. b) Remove the wiring harness cover. − The parts...
Removal and installation − Before you begin removing parts, perform the following operations: a) Remove the glove box. b) Remove the wiring harness cover. − The parts...
Fuel tank
Note: The procedures for replacing the fuel level sensor and fuel pump are provided in the " Fuel tank " chapters " Fuel injection system (MPI) ". Removal and...
Note: The procedures for replacing the fuel level sensor and fuel pump are provided in the " Fuel tank " chapters " Fuel injection system (MPI) ". Removal and...
Accelerator pedal and accelerator pedal position sensor
Removal and installation − The parts are removed in the order of the numbers indicated in the figure "Accelerator pedal". Accelerator pedal. 1 - accelerator pedal...
Removal and installation − The parts are removed in the order of the numbers indicated in the figure "Accelerator pedal". Accelerator pedal. 1 - accelerator pedal...
This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Similar materials for other Mitsubishi models
➤ Power unit: Fuel injection GDI Mitsubishi Colt 4 and 5 (1991-2003)
➤ Power unit: Injection system (GDI) Mitsubishi Carisma (1995-2004)
Link in different formats to this section
TEXTHTMLBB Code
- General information
- User manual
- Maintenance
- Power unit
- Repair of MPI engines
- Repair of GDI engines
- Engine overhaul
- Cooling and lubrication system
- MPI fuel injection system
- GDI fuel injection system
- Intake and exhaust system
- Starting and charging system
- Transmission
- Automatic gearbox
- Variator (CVT)
- Drive shafts and gearbox
- Chassis and running gear
- Front suspension
- Rear suspension
- Steering
- Brake system
- Body and interior
- Doors, locks and windows
- Exterior (external elements)
- Interior (internal elements)
- Electrical equipment
- Heater and air conditioner
- Security system SRS
- Equipment and devices
- Wiring diagrams (saloon)
- Wiring diagrams (wagon)
- General information
- Maintenance
- Power unit
- Engine repair
- Lubrication system
- Cooling system
- Ignition system
- Fuel system
- Carburetor
- Fuel injection
- Diesel power system
- Exhaust system
- Transmission
- Clutch
- Car gearbox
- Chassis and running gear
- Front suspension
- Rear suspension
- Steering
- Brake system
- Wheels and tires
- Body and interior
- Exterior (external elements)
- Interior (internal elements)
- Heating system
- Electrical equipment
- Equipment and devices
- Power devices
- Electrical circuits
