Share with friends:
Car engine ignition system Mitsubishi Lancer 3 and 5
Ignition system — general information
The ignition system generates an ignition spark that ignites the air-fuel mixture in the combustion chamber of the corresponding cylinder. To ensure the formation of a...
The ignition system generates an ignition spark that ignites the air-fuel mixture in the combustion chamber of the corresponding cylinder. To ensure the formation of a...
Precautions when working with the ignition system
Electronic ignition systems can have ignition voltages of up to 30 kV. Under unfavorable conditions, such as humidity in the engine compartment, voltage peaks can break...
Electronic ignition systems can have ignition voltages of up to 30 kV. Under unfavorable conditions, such as humidity in the engine compartment, voltage peaks can break...
Checking the ignition coil
Engines with a capacity of 1.2 / 1.3 / 1.5 l produced from January 1984 to August 1990. The ignition coil is located on the mudguard. The ignition coil primary winding...
Engines with a capacity of 1.2 / 1.3 / 1.5 l produced from January 1984 to August 1990. The ignition coil is located on the mudguard. The ignition coil primary winding...
Checking the ignition wires
If the resistance of the ignition wires increases, difficulties with starting the engine and malfunctions in the ignition system may occur. Disconnect the ground cable...
If the resistance of the ignition wires increases, difficulties with starting the engine and malfunctions in the ignition system may occur. Disconnect the ground cable...
Replacing breaker contacts
Over time, burnouts are formed on the contact surface of the breaker, visible by elevations and craters. In addition, the plastic slider wears out. Because of this, the...
Over time, burnouts are formed on the contact surface of the breaker, visible by elevations and craters. In addition, the plastic slider wears out. Because of this, the...
Checking/adjusting the closing angle
To accurately set the angle of the breaker contacts, a special device for measuring the angle of the closing is used at service stations. This device has the advantage...
To accurately set the angle of the breaker contacts, a special device for measuring the angle of the closing is used at service stations. This device has the advantage...
Checking/setting ignition timing
On engines with a mechanical interrupter ignition system, the ignition timing should be checked, and possibly adjusted, after adjusting the breakaway contacts and as...
On engines with a mechanical interrupter ignition system, the ignition timing should be checked, and possibly adjusted, after adjusting the breakaway contacts and as...
Removal and installation the ignition distributor
The ignition distributor is driven by the camshaft. Until August 1990, it was mounted next to the intake manifold, at the rear of the cylinder head. Since September...
The ignition distributor is driven by the camshaft. Until August 1990, it was mounted next to the intake manifold, at the rear of the cylinder head. Since September...
Spark plugs — general information
The spark plug consists of a central electrode, an insulator with a housing, and a ground electrode. The central electrode is hermetically secured in the insulator, the...
The spark plug consists of a central electrode, an insulator with a housing, and a ground electrode. The central electrode is hermetically secured in the insulator, the...
Recommended spark plug parameters for COLT / LANCER
Serial MITSUBISHI COLT / LANCER vehicles are mostly equipped with spark plugs from NGK or Nippon Denso. The standardization of spark plugs varies among manufacturers....
Serial MITSUBISHI COLT / LANCER vehicles are mostly equipped with spark plugs from NGK or Nippon Denso. The standardization of spark plugs varies among manufacturers....
Ignition system fault diagnostics
Problem: The engine starts poorly or does not start at all 1) This defect can only occur in an ignition system with mechanical interruption.
Problem: The engine starts poorly or does not start at all 1) This defect can only occur in an ignition system with mechanical interruption.
This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Similar materials for other Mitsubishi models
➤ Power unit: Ignition system Mitsubishi Colt 4 and 5 (1991-2003)
➤ Electrical equipment: Ignition system Mitsubishi Outlander 1 (2003-2008)
➤ Power unit: Ignition system Mitsubishi Pajero 1 and 2 (1982-1999)
➤ Power unit: Ignition system Mitsubishi Space Star (1998-2005)
Link in different formats to this section
TEXTHTMLBB Code
- General information
- User manual
- Maintenance
- Power unit
- Repair of MPI engines
- Repair of GDI engines
- Engine overhaul
- Cooling and lubrication system
- MPI fuel injection system
- GDI fuel injection system
- Intake and exhaust system
- Starting and charging system
- Transmission
- Automatic gearbox
- Variator (CVT)
- Drive shafts and gearbox
- Chassis and running gear
- Front suspension
- Rear suspension
- Steering
- Brake system
- Body and interior
- Doors, locks and windows
- Exterior (external elements)
- Interior (internal elements)
- Electrical equipment
- Heater and air conditioner
- Security system SRS
- Equipment and devices
- Wiring diagrams (saloon)
- Wiring diagrams (wagon)
- General information
- Maintenance
- Power unit
- Engine repair
- Lubrication system
- Cooling system
- Ignition system
- Fuel system
- Carburetor
- Fuel injection
- Diesel power system
- Exhaust system
- Transmission
- Clutch
- Car gearbox
- Chassis and running gear
- Front suspension
- Rear suspension
- Steering
- Brake system
- Wheels and tires
- Body and interior
- Exterior (external elements)
- Interior (internal elements)
- Heating system
- Electrical equipment
- Equipment and devices
- Power devices
- Electrical circuits