Share with friends:
Vehicle ignition system Mitsubishi Pajero 1 and 2
Design and description of the ignition system
In most engine modifications, the ignition system is battery-powered and contactless. Engines 2.0, 2.4 and 2.6 l Cylinder numbering, direction of rotation of the...
In most engine modifications, the ignition system is battery-powered and contactless. Engines 2.0, 2.4 and 2.6 l Cylinder numbering, direction of rotation of the...
Ignition system adjustments
2.6L Engine On these engines, only an induction sensor gap check is permitted, which should only be performed after disassembling the ignition distributor and is not a...
2.6L Engine On these engines, only an induction sensor gap check is permitted, which should only be performed after disassembling the ignition distributor and is not a...
Checking the crankshaft speed sensor
There should be 2 voltages on the sensor: +12V DC from battery; 5 V from the processor unit, interrupted when the distributor rotates. 1. Check the sensor on the car,...
There should be 2 voltages on the sensor: +12V DC from battery; 5 V from the processor unit, interrupted when the distributor rotates. 1. Check the sensor on the car,...
Ignition coil and additional resistor — checking
Checking the resistance of the additional resistor Engines 2.0 and 2.6 l 1. Check the resistance of the additional resistor. 2. Check the resistance of the primary...
Checking the resistance of the additional resistor Engines 2.0 and 2.6 l 1. Check the resistance of the additional resistor. 2. Check the resistance of the primary...
Distributor Cap and Rotor — Replacement
1. Remove the cover by releasing the latches or unscrewing the screws. 2. Check the condition of the lid (presence of cracks, traces of puncture, etc.). 3. Remove the...
1. Remove the cover by releasing the latches or unscrewing the screws. 2. Check the condition of the lid (presence of cracks, traces of puncture, etc.). 3. Remove the...
Setting the ignition timing
As a rule, this operation is performed during each cycle of engine adjustment work. The ignition timing is very stable when using automatic adjustment, however, the...
As a rule, this operation is performed during each cycle of engine adjustment work. The ignition timing is very stable when using automatic adjustment, however, the...
Adjusting valve clearances
Setting the stator and rotor of the sensor when measuring the gap 1. Stator 2. Rotor Check the gap between the stator and rotor with a non-magnetic feeler gauge, which...
Setting the stator and rotor of the sensor when measuring the gap 1. Stator 2. Rotor Check the gap between the stator and rotor with a non-magnetic feeler gauge, which...
Adjusting idle speed and mixture quality
Engine Speed Sensor Connector on 2.4L and 3.0L Engine Engine speed sensor connector – indicated by arrows: top - on a 2.4 l engine; below - on a 3.0 l engine. Installing...
Engine Speed Sensor Connector on 2.4L and 3.0L Engine Engine speed sensor connector – indicated by arrows: top - on a 2.4 l engine; below - on a 3.0 l engine. Installing...
Adjusting the mixture composition
Carburetor engines Attention! The mixture adjustment screw is covered with a plug, which should only be broken off in the event of carburetor repair. 1. Remove the...
Carburetor engines Attention! The mixture adjustment screw is covered with a plug, which should only be broken off in the event of carburetor repair. 1. Remove the...
Ignition distributor — removal and installation
Ignition distributor for 2.0 and 2.6 l engines 1. Tip cover; 2. Lid; 3. Coal; 4. Runner; 5. Wire; 6. Ground wire; 7. Ignition unit; 8, 24 Pin; 9. Rotor; 10. Plate; 11....
Ignition distributor for 2.0 and 2.6 l engines 1. Tip cover; 2. Lid; 3. Coal; 4. Runner; 5. Wire; 6. Ground wire; 7. Ignition unit; 8, 24 Pin; 9. Rotor; 10. Plate; 11....
This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Similar materials for other Mitsubishi models
➤ Power unit: Ignition system Mitsubishi Colt 4 and 5 (1991-2003)
➤ Power unit: Ignition system Mitsubishi Lancer 3 and 5 (1984-1992)
➤ Electrical equipment: Ignition system Mitsubishi Outlander 1 (2003-2008)
➤ Power unit: Ignition system Mitsubishi Space Star (1998-2005)
Link in different formats to this section
TEXTHTMLBB Code
- General information
- User manual
- Troubleshooting
- Maintenance
- Technical specifications
- Power unit
- Engine repair
- Cooling system
- Lubrication system
- Fuel system
- Engine management system
- Intake and exhaust system
- Engine electrical equipment
- Transmission
- Clutch
- Manual gearbox
- Automatic gearbox
- Drive shafts
- Chassis and running gear
- Front suspension
- Rear suspension
- Brake system
- Steering
- Body and interior
- Exterior (external elements)
- Interior (internal elements)
- Doors, locks and windows
- Body dimensions
- Electrical equipment
- Safety system (SRS)
- Air conditioner
- Equipment and devices
- Electrical diagrams
- General information
- User manual
- Seats and seat belts
- Instruments and controls
- Driving and operation
- Maintenance
- Power unit
- Gasoline engines
- Diesel engines
- Ignition system
- Engine electrical equipment
- Cooling and lubrication system
- Power and exhaust system
- Fuel system (gasoline)
- Fuel system (diesel)
- Transmission
- Clutch
- Mechanical gearbox
- Automatic gearbox
- Drive shafts and axles
- Chassis and running gear
- Front suspension
- Rear suspension
- Steering
- Brake system
- Body and interior
- Exterior (external elements)
- Interior (internal elements)
- Doors, locks and windows
- Electrical equipment
- Equipment and devices
- Heater and air conditioner
- Cruise control
- Headlights and lighting
- Electrical circuits