Exterior (external elements) of the car Mitsubishi Pajero 4

General information — special tools
Tool Number and name MB990480 Glass Holder MB990900 or MB991164 Door hinge adjustment key MB990925 Bearing and Seal Installation Tool MB990211 Movable hammer MB990784...

Adjusting the hood
Adjusting the bonnet gap 1. Loosen the hood hinge mounting bolts. Move the hood hinge backwards/forwards and left/right to align the hood gap. 2. Tighten the hood hinge...

Removal the hood
1. Remove the radiator grille. 2. Check the hood gap. 3. Remove shock absorber A (1). 4. Remove shock absorber B (2). 5. Remove the feed shock absorber (3). 6. Remove...

Installing the hood
Note: When installing, tighten the bolts to the tightening torques shown in the figure. 1. Install the hood hinge cover (16). 2. Install the hood hinge (15). 3. Install...

Front wing
Removal the front wing 1. Remove the waterproof hood trim. 2. Remove the mudguard. 3. Remove the front door assembly. 4. Remove the front bumper assembly. 5. Remove the...

License plate mounting
Removal the license plate mount 1. Remove the license plate mounting trim. 2. Remove the lower trim of the luggage compartment door. 3. Remove the water-repellent film...

Front bumper
Removal the front bumper 1. Remove the radiator grille. 2. Remove the support. 3. Remove the headlight washer drain. 4. Remove the front part of the front fender liner....

Rear bumper
Removal the rear bumper Short wheelbase 1. Remove the rear combination light. 2. Remove the rear part of the rear fender liner. 3. Remove the rear mudguard. 4....

Radiator grille
Removal the radiator grille 1. Remove the emblem (1). 2. Remove the radiator grille (2). Installing the radiator grille 1. Install the radiator grille (2). 2. Install...

Mudguards — removal and installation
Removal the mudguards 1. Remove the front mudguard. 2. Remove the rivet (1). 1) Make a hole in the rivet to break it using a drill with a 4mm drill bit and remove the...

Moldings — removal and installation
Removal moldings Note: Use a special puller to remove the roof molding. 1. Remove the roof molding (cars without roof rails) (1). 2. Remove the roof slats. 3. Remove the...

Door trims
Removal door trims 1. Remove the front door trim (1). 2. Remove rivet A (2). Note: The procedures for removing the door trim rivets are the same as those for removing...

License plate cover
Removal the license plate cover 1. Remove the right and left lower trim of the luggage compartment door (1). 2. Disconnect the rear fog light connector connection (2)....

Side threshold trim
Removal the side sill trim 1. Remove the side threshold trim (1). 1) Attach protective tape along the edges of the entire length of double-sided tape remaining on the...

Side stand
Removal the side stand 1. Remove the side stand assembly (1). Installing the side stand Note: When installing, tighten the bolts to the tightening torques shown in the...

Engine crankcase protection
Removal the engine crankcase protection 1. Remove the lower skid plate (1). 2. Remove the front lower engine crankcase guard (2). 3. Remove the rear lower engine...

Mudguard
Removal the mudguard 1. Remove the front mudguard (1). 2. Remove the front mudguard bracket (2). 3. Remove the rear mudguard (3). 4. Remove the rear mudguard safety...

Roof rails
Removal roof slats 1. Remove the ceiling trim. 2. Remove the mounting bracket. 3. Remove the roof rail assembly (1). 4. Remove the front roof rail seal (2). 5. Remove...

Rear reflector
Removal the rear reflector 1. Remove the plug (1). 2. Remove the cover (2). 1) Insert special tool MB990784 into the groove of the cover. 2) Press the handle of the tool...

Emblems — removal, installation
Removal emblems 1. Remove the front three-diamond emblem (1). 2. Remove the rear three-diamond emblem (2). 3. Remove the "PAJERO" emblem (3). 4. Remove the "MONTERO"...

Electrically operated exterior rearview mirror system fault diagnostic table
Signs Reasons The power outside mirror system does not work 1. The system fuse has blown. 2. Failure of the mirror adjustment switch. 3. Failure of the electric mirror...

Removal the outside rearview mirrors
1. Remove the front door trim. 2. Remove the outer trim of the front door glass. 3. Remove the outside rearview mirror (1). 4. Remove the mirror (2). Attention: Do not...

Installation of exterior rear view mirrors
Note: When installing, tighten the bolts to the tightening torques shown in the figure. 1. Install the outside rearview mirror adjustment switch (6). 2. Install the...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Similar materials for other Mitsubishi models

➤ Body: Exterior (external elements) Mitsubishi Colt 5 (1995-2003, petrol)
➤ Body and interior: Exterior (external elements) Mitsubishi Lancer 9 (2000-2007, petrol)
➤ Body and interior: Exterior (external elements) Mitsubishi Galant 5 (1983-1989, petrol)
➤ Body and interior: Exterior (external elements) Mitsubishi L200 4 (2005-2014, diesel)
➤ Body and interior: Exterior (external elements) Mitsubishi Outlander 1 (2003-2008)
➤ Body and interior: Exterior (external elements) Mitsubishi Space Star (1998-2005)

Share with friends:

Link in different formats to this section

TEXTHTMLBB Code

Pajero 4 (2006-2021)

Pajero 1 and 2 (1982-1999)