Removal the rear bumper
Short wheelbase
1. Remove the rear combination light.
2. Remove the rear part of the rear fender liner.
3. Remove the rear mudguard.
4. Disconnect the angle sensor connector connection.
5. Disconnect the connector of the parking lights and turn signal (for right-hand drive models).
6. Remove the central part of the rear bumper assembly (1).
7. Remove the rear bumper footrest (2).
8. Remove the central part of the rear bumper (3).
9. Remove the rear bumper corner (4).
10. Remove the rear bumper reinforcement (5).
11. Remove the side light and turn signal lamp (right hand drive model) (6).
12. Remove rivet A (7).
Note: The operations for removing the rivets of the rear bumper are similar to the operations for removing the rivets of the front bumper.
13. Remove the rear bumper side bracket (8).
14. Remove rivet B (9).
Note: The operations for removing the rivets of the rear bumper are similar to the operations for removing the rivets of the front bumper.
15. Remove the dirt trap support (10).
16. Remove the rear bumper side holder (11).
17. Remove the lower cover of the rear bumper (12).
18. Remove the reflector (13).
19. Remove the angle sensor (14).
Back door
1. Remove the rear combination light.
2. Remove the rear part of the rear fender liner.
3. Remove the rear mudguard.
4. Disconnect the angle sensor connector connection.
5. Disconnect the connector of the parking lights and turn signal (for right-hand drive models).
6. Remove the central part of the rear bumper assembly (1).
7. Remove the rear bumper footrest (2).
8. Remove the central part of the rear bumper (3).
9. Remove the rear bumper corner (4).
10. Remove the rear bumper reinforcement (5).
11. Remove the side light and turn signal lamp (right hand drive model) (6).
12. Remove rivet A (7).
Note: The operations for removing the rivets of the rear bumper are similar to the operations for removing the rivets of the front bumper.
13. Remove the rear bumper side bracket (8).
14. Remove rivet B (9).
Note: The operations for removing the rivets of the rear bumper are similar to the operations for removing the rivets of the front bumper.
15. Remove the dirt trap support (10).
16. Remove the lower rear bumper guard (11).
17. Remove the lower side bracket of the rear bumper (12).
18. Remove the reflector (13).
19. Remove the angle sensor (14).
20. Remove the rear bumper support bracket (15).
Installing the rear bumper
Short wheelbase
Note: When installing, tighten the bolts to the tightening torques shown in the figure.
1. Install the angle sensor (14).
2. Install the reflector (13).
3. Install the rear bumper lower cover (12).
4. Install the rear bumper side holder (11).
5. Install the dirt trap support (10).
6. Install rivet B (9).
Note: The installation procedures for the rear bumper rivets are the same as those for the front bumper rivets.
7. Install the rear bumper side bracket (8).
8. Install rivet A (7).
Note: The installation procedures for the rear bumper rivets are the same as those for the front bumper rivets.
9. Install the side light and turn signal lamp (right hand drive model) (6).
10. Install the rear bumper reinforcement (5).
11. Install the rear bumper corner (4).
12. Install the central part of the rear bumper (3).
13. Install the rear bumper footrest (2).
14. Install the rear bumper center assembly (1).
15. Establish the connection of the parking light and turn signal connector (for right-hand drive models).
16. Establish the angle sensor connector connection.
17. Install the rear mudguard.
18. Install the rear part of the rear fender liner.
19. Install the rear combination light.
Long wheelbase
Note: When installing, tighten the bolts to the tightening torques shown in the figure.
1. Install the rear bumper support bracket (15).
(The material is based on data from the website: www.MitsubishiMan.ru)
2. Install the angle sensor (14).
3. Install the reflector (13).
4. Install the lower side bracket of the rear bumper (12).
5. Install the rear bumper lower guard (11).
6. Install the dirt trap support (10).
7. Install rivet B (9).
Note: The installation procedures for the rear bumper rivets are the same as those for the front bumper rivets.
8. Install the rear bumper side bracket (8).
9. Install rivet A (7).
Note: The installation procedures for the rear bumper rivets are the same as those for the front bumper rivets.
10. Install the side light and turn signal lamp (right hand drive model) (6).
11. Install the rear bumper reinforcement (5).
12. Install the rear bumper corner (4).
13. Install the central part of the rear bumper (3).
14. Install the rear bumper footrest (2).
15. Install the central part of the rear bumper assembly (1).
16. Establish the connection of the parking light and turn signal connector (for right-hand drive models).
17. Establish the angle sensor connector connection.
18. Install the rear mudguard.
19. Install the rear part of the rear fender liner.
20. Install the rear combination light.