Car front and rear suspension Mitsubishi Galant 6 and 7

Suspension and steering — design description
Front Suspension Component Layout Diagram for 1992-Pre-Mirage and Diamante Models 1 - Cotter pin; 2 - Drive shaft; 3 - Washer; 4 - Brake mechanism support; 5 -...

Suspension and steering specifications
Wheel alignment angles Wheel alignment front wheels 0±1.86 mm (0° ±18') rear wheels 1.86±1.86 mm (1°18' ±18') 20° wheel rotation divergence 2° Maximum turning angle ...

Removal and installation of struts and coil springs of the front suspension
Front Suspension Strut Installation Details on Mirage Models 1 - Brake hose fastening clamp; 2 - Wheel sensor (models with ABS); 3 - Lower support mounting bolt (2 pcs);...

Restorative repair of front suspension strut assemblies
MacPherson strut design 1 - Rack; 2 - Shock absorber rod boot; 3 - Coil spring (compressed with a special tool); 4 - Upper spring seat washer; 5 - Assembling the upper...

Checking the condition of the upper ball joints of the front suspension (Galant 1994-1998)
1. The support is mounted in the body of the upper suspension arm and, if worn, is replaced together with the latter (see Section Removal and installation the upper arms...

Removal and installation the upper front suspension arms (Galant 1994-1998)
Upper Control Arm Assembly Design (Galant 1994-1998 Models) 1 - Ball joint for fastening the upper arm to the steering knuckle; 2 - Self-locking nuts for fastening the...

Checking the condition of the lower ball joints of the front suspension
1. The support is mounted in the body of the lower suspension arm and, if worn, is replaced together with the latter (see Section Removal and installation the lower arms...

Removal and installation the lower arms of the front suspension
Installation details of the lower arms of the front suspension on Galant models of 1994÷1998. 1 - Nut for fastening the ball joint of the reaction section of the lower...

Removal and installation the front anti-roll bar
Mirage Models Removal 1. Disconnect the negative cable from the battery. Warning! If the car stereo system is equipped with a security code, make sure you have the...

Removal and installation of steering knuckles and hub assemblies with wheel bearings (front suspension)
Design of the front wheel hub assembly for Mirage and Diamante models 1 - Inner seal; 2 - Hub; 3 - Dust shield; 4 - Retaining ring; 5 - Wheel bearing; 6 - Outer seal; 7...

Removal and installation rear struts
Diamante Models Removal 1. Disconnect the negative cable from the battery. Warning! If the car stereo system is equipped with a security code, make sure you have the...

Restorative repair of rear suspension strut assemblies
The design of the rear suspension strut assembly of Mirage and Galant models since 1994. 1 - Protective cover; 2 - Self-locking nut; 3 - Washer; 4 - Upper bushing A; 5 -...

Removal and installation the upper control arms of the rear suspension
Galant models up to 1993. Removal 1. Disconnect the negative cable from the battery. Warning! If the car stereo system is equipped with a security code, make sure you...

Removal and installation the lower control arms of the rear suspension
Galant models up to 1993. Removal 1. Disconnect the negative cable from the battery. Warning! If the car stereo system is equipped with a security code, make sure you...

Removal and installation the rear suspension trailing arms
Galant models up to 1993. Removal 1. Jack up the car and place it on stands. Remove the corresponding rear wheel. 2. Remove the brake drum/disc (see Chapter Brake system...

Removal and installation the rear anti-roll bar
Galant models up to 1993. Removal 1. Jack up the car and place it on supports. 2. Support the rear axle beam with a jack. 3. Loosen the self-locking mounting nuts and...

Adjusting wheel bearings
Mirage Models Attention! Wheel bearings are replaced together with the hubs! 1. Jack up the car and place it on stands. Remove the corresponding rear wheel. 2. Remove...

Removal and installation of hub assemblies
Hub assembly design on Galant models since 1994. 1 - Wheel sensor (models with ABS); 2 - Brake caliper; 3 - Brake drum; 4 - Brake disc; 5 - Support bracket bolt; 6 -...

Removal and installation wheel studs
Hubs of wheels equipped with disc brakes Removal 1. Jack up the car and place it on supports. Remove the corresponding wheel. 2. Remove the brake caliper and pads (see...

Wheels and tires — general information
The wheels of all the models of cars described in this Manual are equipped with radial tires of metric size with fiberglass or steel cord. Installing tires of a...

Wheel alignment angles
Wheel alignment A - The cylinder will roll in a straight line; B - The cone will roll in a circle with the center at the narrow end; C - Diagram of wheel contact with...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Similar materials for other Mitsubishi models

➤ Chassis and running gear: Car suspension Mitsubishi Colt 5 (1995-2003, petrol)
➤ Chassis and running gear: Car suspension Mitsubishi L200 4 (2005-2014, diesel)
➤ Chassis and running gear: Suspension and drive shafts Mitsubishi Space Star (1998-2005)

Share with friends:

Link in different formats to this section

TEXTHTMLBB Code