Dismantling the car engine Mitsubishi Galant 6 and 7

This chapter is devoted to locksmith work on the removal and installation of the power unit and the dismantling of its components and parts.

Engine specifications
Where: MFI = Multi-point fuel injection system MFI-T = Multiport Fuel Injection with Turbocharging SOHC = Single Overhead Camshaft Engines DOHC = Double Overhead...

Removal and installation the engine
Preparation Prepare a container to receive the drained working fluids; Consider a method for marking all disconnected communication lines (wires, hoses, tubes, etc.);...

Removal and installation the cylinder head cover
Except for 3.0L (SOHC and DOHC) and 3.5L engines Removal 1. Disconnect the negative cable from the battery. If your car stereo system is equipped with a security code,...

Removal and installation of valve drive assemblies
1.5L Engine Valve Train Assembly Components 1 - Breather pipe; 2 - PCV hose; 3 - Cylinder head cover; 4 - Sealing gasket; 5 - Seal; 6 - Valve drive assembly; 7 - Valve...

Removal and installation the thermostat
To avoid burns, proceed with work only after the system has completely cooled down! Do not allow antifreeze to come into contact with exposed areas of the body or...

Removal and installation the intake manifold
Intake manifold and exhaust manifold installation details for 1.5L models (4G15 engine) 1 - Power unit lifting eye; 2 - Intake manifold support stand; 3 - Inlet...

Removal and installation the exhaust manifold
Exhaust manifold installation details for 1.5L models 1 - Exhaust manifold cover A; 2 - Oxygen sensor (federal models 1992 and 1993); 3 - Power unit lifting eye; 4 -...

Removal and installation a turbocharger
Turbocharger Assembly Installation Details for 1990-1993 Galant Models Equipped with 2.0L DOHC Engine (1 of 2) 1 - Radiator; 2 - Air supply hose connection branch pipe;...

Removal and installation the cooling system radiator (all models)
Removal 1. Disconnect the negative cable from the battery. If your car stereo system is equipped with a security code, make sure you have the correct combination to...

Removal and installation the engine cooling system fan
Fan assembly installation details on Diamante models 1 - Drain valve; 2 - Radiator cap; 3 - Overflow tube; 4 - Expansion tank; 5 - Upper radiator hose; 6 - Lower...

Removal and installation the water pump
Water Pump Installation Details for Mirage Models Equipped with 1.5L (4G15) Engine 1 - Water pump pulley; 2 - Steering pump support bracket (models with power steering);...

Removal and installation the cylinder head
1.5L engines Removal 1. Relieve pressure in the fuel system. Remember that gasoline is highly flammable! When working with fuel system components, observe all accepted...

Removal and installation the engine oil pan
1.5L engines Oil pan installation details for Mirage 1.5L models (4G15 engine) 1 - Transmission dome cover; 2 - Drain plug; 3 - Sealing washer; 4 - Oil pan Removal 1....

Removal and installation the oil pump
Oil pump installation details on 1.5L models 1 - Full flow oil filter; 2 - Drain plug; 3 - Sealing washer; 4 - Oil pan; 5 - Oil intake with mesh filter; 6 - Sealing...

Removal and installation the crankshaft vibration damper
Removal 1. Disconnect the negative cable from the battery. If your car stereo system is equipped with a security code, make sure you have the correct combination to...

Removal and installation the timing belt cover and timing belt
Timing belt cover and component installation details for 1.5L models produced in 1990÷1994. 1 - Drive belt; 2 - Steering pump pulley; 3 - Water pump pulley; 4 -...

Replacing the front crankshaft oil seal
Note: The authors of this Manual recommend replacing the front crankshaft oil seal during the timing belt removal/installation procedures (see Section Removal and...

Removal and installation camshafts and valve lifters
Valve train component installation details for 1.5L models 1 - Breather pipe; 2 - PCV hose; 3 - Cylinder head cover; 4 - Sealing gasket; 5 - Seal; 6 - Valve drive rocker...

Removal and installation the balance shaft
Details of installation of balance shafts on 2.0 l and 2.4 l engines 1 - Oil filter; 2 - Oil cooler bolt *3; 3 - Oil cooler *3; 4 - Drain plug; 5 - Sealing washer; 6 -...

Replacing the rear crankshaft oil seal
Crankshaft Rear Oil Seal Installation Details (All Models) 1 - Adapter plate; 2 - Landing plate; 3 - Back plate; 4 - Oil seal housing; 5 - Seal; 6 - Bearing cover...

Removal and installation the flywheel/drive disc
Removal 1. Disconnect the negative cable from the battery. If your car stereo system is equipped with a security code, make sure you have the correct combination to...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Similar materials for other Mitsubishi models

➤ Power unit: Engine in a car Mitsubishi Colt 2 and 3 (1983-1993)
➤ Power unit: Engine repair Mitsubishi Lancer 3 and 5 (1984-1992)
➤ Power unit: Engine repair Mitsubishi Outlander 1 (2003-2008)
➤ Power unit: Engine repair Mitsubishi Pajero 4 (2006-2021)

Share with friends:

Link in different formats to this section

TEXTHTMLBB Code