Car engine repair Mitsubishi Colt 2 and 3

Engine specifications
General Cylinder firing order 1-3-4-2 Cylinder numbering (from timing belt to gearbox) 1-2-3-4 1.5L engines Camshaft Axial clearance of the camshaft 0.05-0.20 mm Cam...

General information and engine identification
All Mitsubishi models described in this manual are equipped with two types of four-cylinder engines: single overhead camshaft (SOHC) engines and double overhead camshaft...

Repair operations that can be carried out without removing the engine from the vehicle
a. Before doing any work, clean the engine compartment and the outside of the engine with some solvent. b. To prevent damage to the paintwork of the front parts of the...

Valve cover — removal and installation
1. Disconnect the negative battery cable. 2. Remove the air filter. 3.3 Carefully disconnect the spark plug wires from the clamps 3. Disconnect the spark plug wires and...

Rocker arms — removal, inspection and installation
Removal 1. Remove the valve cover. 2. Set the first piston to top dead center. 4.3 Remove the bolts (indicated by arrows) securing the rocker arm shafts - the picture...

Valve springs, fasteners and linings — replacement
Caution! Broken valve springs and damaged valve linings can be replaced without removing the cylinder head. 1. Remove the valve cover. 2. Unscrew the spark plug from the...

Hydraulic valve regulators — removal, inspection and installation
6.1 Hydraulic valve adjusters are located at the rear of the rocker arms 1. Remove the rocker shafts together with the rocker arms and remove the adjusters from the...

Timing Belt and Sprockets — Removal, Checking and Installation
Caution! Do not attempt to rotate the crankshaft using the bolt located on the crankshaft sprocket, do not rotate the crankshaft counterclockwise, and do not rotate the...

Front Crankshaft Oil Seal — Replacement
1. Remove the timing belt and crankshaft sprocket. 8.2 Carefully remove the seal using a small screwdriver 2. Wrap the tip of the screwdriver with insulating tape....

Camshafts — Removal, Inspection and Installation
Removal 1. Set piston N1 to top dead center. 2. Disconnect the wire from the negative terminal of the battery. 3. Remove the valve cover. 4. Remove the ignition...

Intake manifold — removal and installation
1. Release the pressure in the fuel system and disconnect the wire from the negative terminal of the battery. 2. Drain the coolant from the cooling system. Removal...

Exhaust manifold — removal and installation
Attention! Before starting work, be sure to let the engine cool down completely. Removal 1. Disconnect the negative battery cable. On 16-valve Galant SOHC and DOHC...

Cylinder head — removal and installation
Removal 1. Set piston N1 to TDC. 2. Disconnect the wire from the negative terminal of the battery. 3. Drain the coolant from the cooling system and unscrew the spark...

Oil pan — removal and installation
Removal 1. Disconnect the negative battery cable. 2. Raise the vehicle and support it on supports. 3. Remove the oil pan from under the engine, remove the dipstick and...

Oil pump — removal, inspection and installation
Removal 1. Remove the timing belt and camshaft sprocket. 2. Remove the oil pan. 14.3 The oil intake pipe is attached with two bolts (indicated by arrows) to the rear of...

Flywheel — removal and installation
Removal 1. Raise and support the vehicle. Remove the transmission. If it is leaking, replace the front gasket. 2. Remove the clutch pressure plate. Check the clutch...

Rear Crankshaft Oil Seal — Replacement
1. Remove the gearbox from the vehicle. 16.2a Quick method for replacing the seal (1.5 l) 16.2b Lubricate the seal with clean engine oil and carefully tap it into place...

Engine Mounts — Checking and Replacing
1. Worn or broken engine mounts must be replaced immediately. Examination 2. When checking, the engine must be raised slightly to relieve pressure from the mounts. 3....

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Similar materials for other Mitsubishi models

➤ Power unit: Repair of MPI engines Mitsubishi Lancer 9 (2000-2007, petrol)
➤ Power unit: Engine repair Mitsubishi Galant 5 (1983-1989, petrol)
➤ Power unit: Engine repair Mitsubishi Outlander 1 (2003-2008)
➤ Power unit: Engine repair Mitsubishi Pajero 4 (2006-2021)

Share with friends:

Link in different formats to this section

TEXTHTMLBB Code