Electrical equipment of the car engine Mitsubishi Colt 2 and 3

Technical characteristics of the ignition system
Distributor pickup coil gap Cordia and Tredia 1983 10.2-0.45 mm 1984 and 1985 1.8L 0.2-0.45 mm 2. 0L 0.77 mm 1986 0.2-0.45 mm 1987 and 1988 1.8L - 2. 0L 0.2-0.45 mm...

General information about the engine electrical equipment
The engine electrical system includes all elements of the ignition system, battery charging and engine starting. When maintaining electrical equipment, observe the...

Battery — Removal and Installation
Caution: Always disconnect the negative terminal wire first and reconnect it last. 3.1 To remove the battery... 1. Disconnect the negative battery cable.; 2. Disconnect...

Battery and wires — check and replace
Periodically inspect the wires for damage, cracks, broken insulation or corrosion. Check the condition of the contacts and clean them from corrosion. Always disconnect...

Ignition system — general description and precautions
When working with the ignition system, observe the following precautions: a) Do not turn on the ignition for more than 10 seconds if the engine does not start. b) Ensure...

Ignition system — check
6.1 Disconnect the high-voltage wire and connect it to a grounded ignition sensor - a spark should break through between the wire and the sensor when the engine...

Ignition Coil — Checking and Replacing
Examination Distributorless Ignition System (DIS) Primary winding (1989) 7.1 Identifying the Primary Ignition Coil Connector Terminals for 1989 Models Without...

Ignition distributor — removal and installation
Removal 1. Disconnect the negative battery cable. 2. Disconnect the coil high tension wire from the distributor cap. 3. Disconnect the vacuum hoses from the ignition...

Vacuum corrector of ignition timing angle — check and replacement
1. Disconnect the vacuum hose from the vacuum corrector and plug it. Then disconnect and plug the second hose. 2. Install the stroboscope and connect the vacuum pump to...

Igniter — Replacement
12.7a Distributor components for Cordia and Tredia 2.0L (1984 and 1985), Galant (1985 and 1986), Colt, Lancer, Miraqe 1.5L (1985-1988) and Precis (1987-1989) 1....

Checking and replacing the pickup coil
Cordia / Tredia 1.8L Turbo (1984 and 1985); Colt, Lancer, Mirage 1.6L (1985) 1. Remove the distributor cap and rotor. 11.2 On Cordia/Tredia 1.8L Turbo models (1984 and...

Centrifugal regulator — checking and replacing elements
1. Disconnect the vacuum hoses from the vacuum corrector. 2. Connect the strobe light. 3. Start the engine. 4. Check that the ignition timing angle increases with...

Distributor Ignition Distributor Receiving Coil Air Gap — Checking and Adjusting
13.1 To adjust the air gap, loosen the mounting screws, insert a feeler gauge between the igniter and one of the rotor protrusions, press the igniter against the feeler...

Battery Charging System — General Description and Precautions
The battery charging system includes the alternator, voltage regulator, battery, jumper wires and connecting wires. Observe the following precautions when working with...

Battery charging system — check
1. If the battery charging system is faulty, before checking the generator, check the following: a) Check the tension and condition of the generator drive belt, mounting...

Generator — removal and installation
Cordia, Precis and Tredia 1. Remove the power steering pump and alternator drive belts. 16.2 Generator mounting elements on Cordia and Tredia models (other models are...

Voltage Regulator / Generator Brushes — Replacement
1988 Precis (with Bosch generator) 1. Remove the generator. 17.2 To remove the voltage regulator/brush holder, unscrew the two mounting screws (indicated by arrows) and...

Engine Starting System — General Description and Precautions
The engine starting system consists of a starter, a solenoid and connecting wires. When working with the starting system, observe the following precautions: a) Do not...

Starter — check
1. If the starter does not operate when the ignition is turned on, check that the automatic transmission lever is in neutral or park (for models with automatic...

Starter — removal and installation
1. Disconnect the negative battery cable. 2. Mark and disconnect the wires from the starter. 20.3 Starter fastening elements 3. Unscrew the mounting bolts (20.3) and...

Starter Solenoid Relay — Removal and Installation
1. Disconnect the negative battery cable. 2. Remove the starter. 21.3 To remove the starter solenoid, unscrew the nut and disconnect the wire (indicated by the arrow)......

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Similar materials for other Mitsubishi models

➤ Power unit: Engine electrical equipment Mitsubishi Galant 5 (1983-1989, petrol)
➤ Power unit: Engine electrical equipment Mitsubishi Pajero 1 and 2 (1982-1999)
➤ Power unit: Engine electrical equipment Mitsubishi Carisma (1995-2004)

Share with friends:

Link in different formats to this section

TEXTHTMLBB Code