Share with friends:
Car carburetor repair Mitsubishi Colt 5 (CJ)
Carburetor Aisan 28/32 — design description
The Aisan 28/32 carburetor installed on Mitsubishi cars is a two-barrel carburetor with a falling flow, sequential opening of the throttle valves and vacuum control of...
The Aisan 28/32 carburetor installed on Mitsubishi cars is a two-barrel carburetor with a falling flow, sequential opening of the throttle valves and vacuum control of...
Cold Fuel Heater — Check
1. Never allow the heater to fall from a height of more than 30 cm. If the element has fallen from a greater height, it can no longer be used. 2. The heater is subject...
1. Never allow the heater to fall from a height of more than 30 cm. If the element has fallen from a greater height, it can no longer be used. 2. The heater is subject...
Disassembly and assembly of carburetor types «A» and «B»
The disassembled carburetor of type "A" is shown in Figure 10.7a-g, and the carburetor of type "B" is shown in Figure 10.8. Figure 10.7a. Type "A" carburetor: 1 - Clamp;...
The disassembled carburetor of type "A" is shown in Figure 10.7a-g, and the carburetor of type "B" is shown in Figure 10.8. Figure 10.7a. Type "A" carburetor: 1 - Clamp;...
Disassembly and assembly of carburetor type «C» and «D»
The type "C" carburetor is shown in Figure 10.25a-c, and the type "D" carburetor is shown in Figure 10.26a,b. Figure 10.25a. Type "C" carburetor: 1 - Cooling system...
The type "C" carburetor is shown in Figure 10.25a-c, and the type "D" carburetor is shown in Figure 10.26a,b. Figure 10.25a. Type "C" carburetor: 1 - Cooling system...
Variable Vent Carburetor (VV)
The assembled carburetor is shown in Figure 10.35a, and disassembled in Figure 10.35b. Figure 10.35a. Assembled carburetor: 1 - Hairpin; 2 - Bolt; 3 - Carburetor; 4 -...
The assembled carburetor is shown in Figure 10.35a, and disassembled in Figure 10.35b. Figure 10.35a. Assembled carburetor: 1 - Hairpin; 2 - Bolt; 3 - Carburetor; 4 -...
Disassembling a carburetor with a variable diffuser diameter
When disassembling the carburetor, the following parts must not be removed: 1. Throttle valve and shaft; 2. Painted adjusting screw; 3. Carburetor body. Float chamber 1....
When disassembling the carburetor, the following parts must not be removed: 1. Throttle valve and shaft; 2. Painted adjusting screw; 3. Carburetor body. Float chamber 1....
Installing a carburetor with a variable diffuser diameter
Caution! Do not damage the piston, diffuser surface, carburetor body opening or main fuel jet with the brush. Do not wash the compensator. Make sure that no dust gets...
Caution! Do not damage the piston, diffuser surface, carburetor body opening or main fuel jet with the brush. Do not wash the compensator. Make sure that no dust gets...
Technical data of the electronic carburetor
Technical data of the electronic carburetor are given in Table 10.1. Table 10.1. Technical data of the electronic carburetor Parameters Nominal value Resistance of the...
Technical data of the electronic carburetor are given in Table 10.1. Table 10.1. Technical data of the electronic carburetor Parameters Nominal value Resistance of the...
Fuel pump — design description
The fuel pump of 8-valve 4G1 engines is shown in Figure 10.67, 12-valve 4G1 engines - in Figure 10.68. Figure 10.67. Fuel pump for 8-valve 4G1 engines: 1 - Fuel drain...
The fuel pump of 8-valve 4G1 engines is shown in Figure 10.67, 12-valve 4G1 engines - in Figure 10.68. Figure 10.67. Fuel pump for 8-valve 4G1 engines: 1 - Fuel drain...
Electronic carburetor — design description
The assembled carburetor is shown in Figure 10.69, and disassembled in Figures 10.70-10.72. Figure 10.69. Assembled carburetor: 1 - Cooling system pipe; 2 - Bolt; 3 -...
The assembled carburetor is shown in Figure 10.69, and disassembled in Figures 10.70-10.72. Figure 10.69. Assembled carburetor: 1 - Cooling system pipe; 2 - Bolt; 3 -...
This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Similar materials for other Mitsubishi models
➤ Power unit: Carburetor Mitsubishi Lancer 3 and 5 (1984-1992)
Link in different formats to this section
TEXTHTMLBB Code
- General information
- User manual
- Specifications
- Gasoline engines
- 4G1 engines until 1995
- 4G1 engines since 1995
- Repair of 4G9 engines
- Cooling system
- Reduced exhaust gas toxicity
- Engine electrical equipment
- Injection system MPI
- Carburetors
- Transmission
- Clutch and drive shafts
- Manual gearbox F4M21/F5M21
- Manual gearbox F4M41
- Automatic gearbox F4A21
- Automatic gearbox F4A41
- Chassis and running gear
- Car suspension
- Steering
- Brake system
- Body
- Exterior (external elements)
- Electrical equipment
- Equipment and devices
- Electrical circuits
- General information
- Maintenance
- Power unit
- Engine in a car
- Engine repair (gasoline)
- Engine repair (diesel)
- Lubrication system
- Cooling system
- Carburetor
- Fuel injection MPI
- Fuel injection GDI
- Emission reduction
- Fuel system (diesel)
- Ignition system
- Exhaust system
- Transmission
- Clutch
- Manual gearbox
- Automatic gearbox
- Drive shafts
- Chassis and running gear
- Chassis malfunctions
- Front suspension
- Rear suspension
- Steering
- Wheels and tires
- Brake system
- Body and interior
- Body elements
- Electrical equipment
- Equipment and devices
- Power devices
- Heating and air conditioning
- Electrical circuits
- General information
- User manual
- Daily care
- Maintenance
- Power unit
- Engine in a car
- Engine overhaul
- Cooling system
- Heater and air conditioner
- Power and exhaust system
- Engine electrical equipment
- Emission reduction
- Transmission
- Mechanical gearbox
- Automatic gearbox
- Clutch and axles
- Chassis and running gear
- Brake system
- Car suspension
- Steering
- Body and interior
- Body and elements repair
- Electrical equipment
- Equipment and devices
- Electrical circuits