Vehicle power and exhaust system Mitsubishi Colt 2 and 3

Technical characteristics of the power supply system
Air damper heating element resistance 6 Ohm at room temperature Engine speed at fast idle 1800 rpm Resistance of electromagnetic valves Ventilation valve 80 0m Fuel...

General description of the power supply system
Models with carburetor engine On these models, the fuel system consists of a fuel tank, two fuel filters, a fuel pump, an air filter and a two-chamber carburetor. The...

Releasing pressure from the fuel system (fuel injection models)
1. Remove the fuel tank filler cap. 2.2 Disconnect the fuel pump connection connector 2. Start the engine and disconnect the fuel pump connection connector (2.2). 3....

Fuel Pump / Fuel Pressure — Check
Fuel pump - check Models with carburetor engine Warning! Be careful when working with gasoline! 1. Check fuel lines for leaks. 2. If no leak is found, check the fuel...

Fuel lines and connections — checking and replacing
Examination 1. Periodically check all hoses and tubes for cracks, so that they are not pinched or deformed. Check the reliability of the fasteners. Replacement 2. When...

Fuel pump — removal and installation
Mechanical pump (models with carburetor engine) 1. Disconnect the negative battery cable. Remove the radiator filler cap. Remove the air filter. 5.2 Disconnect the fuel...

Fuel tank — removal and installation
Removal 1. Unscrew the fuel filler cap and release the pressure from the fuel system. Disconnect the negative battery cable. Drain the remaining fuel in the tank through...

Air filter — removal and installation
1. Remove the cover and filter element. On models with multi-point fuel injection, remove the accumulator, air supply hose and air flow sensor. 2. Disconnect any wires...

Carburetor — removal and installation
Removal 1. Remove the fuel filler cap. Remove the air cleaner. Disconnect the accelerator cable from the throttle lever. On automatic transmission models, disconnect the...

Carburetor — diagnostics and overhaul
Diagnostics 1. Before checking the carburetor, the following elements must be checked: a) Check all vacuum hoses and diaphragms for leaks and proper installation. b)...

Carburetor — checking and adjustment
Adjusting idle speed and fuel mixture composition 1. Look Chapter 1 . Checking the fast idle system 11.2a Inspect the fast idle diaphragm hose (1) for cracks and wear -...

Fuel injection system — check
1. Check all connecting wires and connectors. Check the battery charge and air filter. Check the air pipes and vacuum hoses of the system. 2. On models with multi-point...

Throttle body (models with two-point fuel injection TBI)
Removal 1. Release the pressure from the fuel system. Disconnect the negative battery cable. Drain the coolant. Disconnect all necessary hoses, wires and pipes. 2. Mark...

Fuel filter — general description
14.2 Components of the air conditioner intake pipe. 1. Pressure relay; 2. Air conditioning system pipes; 3. Bolt; 4. Viewing window 1. The models covered by this manual...

Multi-Point Fuel Injection (MPI) System
Throttle body 1. Disconnect the throttle return spring and disconnect the accelerator cable. 2. Label and disconnect all wires and hoses. 3. Unscrew the four fastening...

Accelerator cable — removal, installation and adjustment
Models without cruise control Cordia, Tredia, Colt, Lancer, Mirage (except MPI) and Precis (except MPI) 1. On carburetor engines, remove the air filter. 16.2 Loosen the...

Exhaust System Maintenance — General Description
17.1a Check the condition of the exhaust system each time the vehicle is raised (Precis model shown) A. Front mount; B. Middle mount; C. Rear mount 1. Regularly check...

Turbocharger — General Description
18.1 Turbocharger Elements 1. Heat shields; 2. Gasket; 3. Bypass valve; 4. Vacuum hose; 5. Turbocharger; 6. Oil supply pipe; 7. Return line hose 1. A turbocharger is...

Turbocharger — check
Warning! Operating the turbocharger without filters and air ducts can cause damage to the turbine blades and personal injury. 1. Check if the turbocharger makes a smooth...

Turbocharger — removal and installation
18.1 Turbocharger Elements 1. Heat shields; 2. Gasket; 3. Bypass valve; 4. Vacuum hose; 5. Turbocharger; 6. Oil supply pipe; 7. Return line hose 1. Remove the heat...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Similar materials for other Mitsubishi models

➤ Power unit: Diesel power system Mitsubishi Lancer 3 and 5 (1984-1992)
➤ Power unit: Fuel and exhaust system Mitsubishi Galant 5 (1983-1989, petrol)
➤ Power unit: Fuel system Mitsubishi L200 4 (2005-2014, diesel)
➤ Power unit: Fuel system (diesel) Mitsubishi Pajero 1 and 2 (1982-1999)
➤ Power unit: Diesel supply system F9Q1 Mitsubishi Space Star (1998-2005)

Share with friends:

Link in different formats to this section

TEXTHTMLBB Code