Car engine cooling system Mitsubishi Colt 4 and 5

General description of the cooling system
Cooling system diagram 1 - coolant pump; 2 - pipeline; 3 - cylinder block; 4 - thermostat; 5 - thermostat housing; 6 - heater radiator; 7 - radiator. All vehicles are...

Elements of the cooling system
SOHC Engine Cooling System Components 1 - coolant pump; 2 - bracket; 3 - thermostat housing; 4 - coolant temperature alarm sensor; 3 - thermostat; 6 - thermostat cover;...

Checking the level and adding coolant
Examination Despite the presence of a warning light for temperature and coolant level, you should not rely entirely on it and, from time to time, check the coolant level...

Draining, flushing and filling the cooling system
Draining the coolant The vehicle must be on a level surface. Drain the coolant as follows: If the engine is cold, unscrew the radiator cap and expansion tank cap. If the...

Radiator — removal, cleaning and installation
Radiator mounting elements 1 - radiator; 2 - expansion tank; 3, 5 - upper radiator support; 4 - radiator cap; 6 - Upper radiator hose; 7 - drain plug; 8 - Automatic...

Thermostat — Removal, Checking and Installation
All models are equipped with a housingless thermostat. Disconnect the ground cable from the battery. Drain the coolant. Remove all parts that restrict access to the...

Coolant pump — removal and installation
Removal Place the vehicle on a lift or overpass or use an inspection pit. Drain the coolant into a special container. Remove the front timing belt cover. Remove the...

Electric Fan — Removal and Checking
The electric cooling fan is secured to the radiator shroud. To remove it, disconnect the shroud (3) from the radiator, disconnect the fan plug and remove the fan (2)...

Coolant Temperature Sensor — Removal, Installation and Testing
Petrol engines are equipped with 2 temperature sensors, diesel engines have one dual temperature sensor. They consist of an NTC element (NTC - negative temperature...

Troubleshooting on the road
If the fan stops while driving, do the following. Disconnect the plug from the thermal relay. Short-circuit the two contacts of the plug with a piece of insulated wire....

Expansion tank — removal and installation
The coolant expansion tank is located in the engine compartment on top of the left mudguard and is maintenance-free. It is very important not to remove the tank cap...

Antifreeze and corrosion inhibitors — general information
If the temperature is expected to drop below 0°C, it is necessary to drain some of the water and add the appropriate amount of ethylene glycol antifreeze to the cooling...

Cooling System Hoses — Maintenance and Repair
Coolant line components 1 - cooling system pipeline; 2 - lower radiator hose; 3 - thermostat housing; 4 - heater hose; 3 - hoses; A - DOHC models; B - SOHC models....

Diagnostics of cooling system faults
The engine cooling system ensures its operation in an optimal temperature range of 82-95°C under various operating conditions. NOTE: Some vehicle models have a different...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Similar materials for other Mitsubishi models

➤ Power unit: Cooling and lubrication system Mitsubishi Lancer 9 (2000-2007, petrol)
➤ Power unit: Cooling and heating Mitsubishi Galant 6 and 7 (1987-1998)
➤ Power unit: Cooling and lubrication system Mitsubishi Outlander 1 (2003-2008)
➤ Power unit: Cooling and lubrication system Mitsubishi Pajero 1 and 2 (1982-1999)
➤ Power unit: Cooling system Mitsubishi Space Star (1998-2005)

Share with friends:

Link in different formats to this section

TEXTHTMLBB Code