Car clutch and drive shafts Mitsubishi Colt 5 (CJ)

General information about the clutch
The clutch used is a single-disc dry clutch with hydraulic drive and diaphragm spring. Clutch maintenance data are provided in Table 11.1. Table 11.1. Clutch maintenance...

Checking and adjusting the clutch pedal
1. Fold back the mat under the clutch pedal. 2. Measure the height A of the clutch pedal (Figure 11.1). Nominal value A: 162-165 mm. Figure 11.1. Measuring the height A...

Clutch pedal — design description
The clutch pedal is shown in Figure 11.5. Figure 11.5. Clutch pedal: 1 - Clutch master cylinder mounting nut; 2 - Clutch master cylinder bracket mounting nut; 3 - Fork...

Clutch Master Cylinder — Design Description
The clutch master cylinder is shown in Figure 11.6. Figure 11.6. Clutch master cylinder: 1 - Retaining ring; 2 - Push rod; 3 - Sealing; 4 - Piston; 5 - Expansion tank...

Clutch hydraulic drive — design description
The hydraulic clutch drive is shown in Figure 11.7a-g, and the cable drive is shown in Figure 11.7d. Figure 11.7a. Clutch hydraulic drive: 1 - Pin; 2; 4 - Adapters; 3 -...

Checking the clutch
Clutch housing cover 1. Check the end of the diaphragm spring for wear and uneven height. Replace the clutch housing cover with a new one if excessive wear or height...

Clutch slave cylinder — design description
The clutch slave cylinder is shown in Figure 11.9. Figure 11.9. Clutch slave cylinder: 1 - Valve head; 2 - Spring; 3 - Rod; 4 - Protective cover; 5 - Piston and seal; 6...

Clutch specifications since 1996
Technical data of the clutch are given in Table 11.3. Table 11.3. Clutch technical data Name Manual transmission F5M41 with engines 4G13, 4G15 Manual transmission F5M41...

Clutch removal and installation since 1996
The clutch installed with the F5M41 gearbox is shown in Figure 11.10. Figure 11.10. Clutch installed with F5M41 gearbox: 1 - Clutch hydraulic tube mounting bracket; 2 -...

Clutch slave cylinder since 1996
The clutch slave cylinder installed with the F5M41 gearbox is shown in Figure 11.11. Figure 11.11. Clutch slave cylinder installed with the F5M41 gearbox: 1 - Cap; 2 -...

Tightening torques of clutch elements and parts
Tightening torques of clutch elements and parts Fastening elements Tightening torque, Nm Clutch housing cover bolt 15-22 Slave cylinder mounting bolt 15-22 Gearbox bolt...

Wheel drive — design description
The bearing and the hub of the front wheel are pressed into the housing of the steering knuckle (Figure 11.347). The axle shaft consists of constant velocity joints of...

Front and rear wheel hub
The front wheel hub is shown in Figure 11.348a, b, the rear wheel hub is shown in Figure 11.348c. Figure 13.348a. Front wheel hub: 1 - Front wheel speed sensor (for...

Wheel drive axle shaft — design description
The wheel drive axle shaft is shown in Figure 11.350a,b. Figure 11.350a. Wheel drive axle shaft: 1 - Front wheel speed sensor (for vehicles with ABS); 2 - Brake hose...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Similar materials for other Mitsubishi models

➤ Transmission: Clutch Mitsubishi Lancer 3 and 5 (1984-1992)
➤ Transmission: Clutch and drive shafts Mitsubishi Galant 5 (1983-1989, petrol)
➤ Transmission: Clutch Mitsubishi L200 4 (2005-2014, diesel)
➤ Transmission: Clutch Mitsubishi Outlander 1 (2003-2008)
➤ Transmission: Clutch Mitsubishi Pajero 1 and 2 (1982-1999)
➤ Transmission: Clutch Mitsubishi Carisma (1995-2004)

Share with friends:

Link in different formats to this section

TEXTHTMLBB Code