Contents: Safety precautions when performing…⤓ Car body care ⤓ Conservation ⤓ Polishing ⤓ Removal tar stains ⤓ Insect Removal ⤓ Removal of building solutions ⤓ Care of parts made of artificial…⤓ Glass washing ⤓ Caring for rubber seals ⤓ Wheel rims ⤓ Seat belts ⤓ Fabric coverings ⤓
The car body is load-bearing.
It is constructed from stamped and welded components, including crumple zones at the front and rear and a rigid center section.
Safety precautions when performing welding work
When performing welding or other work involving strong sparking near the location of the battery, be sure to remove it.
It is prohibited to weld, hard or soft solder parts of a filled air conditioner. This also applies to those parts of the car, the welding of which can cause heating of the air conditioner parts. When carrying out repair and painting work in a drying oven or in its heating zone, the temperature should not exceed +80°C.
Car body care
Check the condition of the body regularly. Otherwise, corrosion of individual sections of the body can lead to severe damage and expensive repairs in the future. It is necessary to pay attention to hidden parts of the car, such as the bottom, wheel arches and the lower part of the engine compartment, as well as parts of the body under the upholstery. The main element of car body care is washing. Before washing the car, soak the remains of insects and remove them from the surface of the body. Wash the body with plenty of water, a soft sponge or brush. Do not wash the paintwork with a strong jet of water. Hose the car and wash off the dirt from top to bottom. Rinse the sponge frequently. Wipe the car with a clean rag. Use only high-quality degreasing detergents. To protect the surface of the body, add detergent preservatives to the water for washing. Do not wash and dry the car in the sun, as stains may remain on the surface of the body. Salt sprinkled on the roads has a harmful effect on the car body.
After washing the car, the effectiveness of the brakes decreases due to humidity. It is recommended to dry the brake discs by briefly pressing the brake pedal at the start of movement.
Conservation
1. Cleanly washed and dried varnish coating must be treated with preservatives every 3 months to protect the car surface from atmospheric influences, creating a non-porous water-repellent wax layer.
2. Any leaked fuel, oil or grease, as well as brake fluid, must be removed immediately, otherwise the color of the paintwork will change.
3. The surface treatment must be repeated if the water does not form drops but spreads over the surface. Regular treatment with preservatives helps to maintain the shine of the varnish coating.
4. There is another way to protect varnish coatings – using washing preservatives. However, washing preservatives provide reliable protection of varnish coatings only if they are used at every car wash and not less than every 2-3 weeks.
5. After using detergents (foaming agents), additional surface treatment with preservatives is especially recommended.
Attention! Preservation must not be carried out in direct sunlight.
Polishing
1. Polishing of the paintwork is necessary only if it has faded due to insufficient care, exposure to dust, harmful gases, weather conditions, and preservatives cannot restore its shine.
2. Do not use coarse polishing pastes and chemically active agents, despite the previously good results.
3. Before polishing, the car must be washed and thoroughly dried. Then follow the instructions for using polishing agents.
4. Polish in small sections to avoid premature drying of the polish. After processing the surface with some polishing agents, additional conservation is required. Polishing in the open sun is prohibited. Matte varnish surfaces cannot be treated with preservatives and polishing agents.
Removal tar stains
Bitumen stains quickly penetrate the paintwork, so they can no longer be completely removed. Fresh stains can be removed with a soft cloth soaked in a special liquid for removing bitumen stains. In emergency cases, you can use regular gasoline, kerosene or turpentine.
Insect Removal
Insects contain substances that can damage the varnish layer if not removed quickly. Use a mild, slightly warm soap or detergent solution or a special insect remover.
Removal of building solutions
Splashes of construction materials are washed off with a slightly warm solution of neutral detergents. Do not rub hard, otherwise you will scratch the varnish coating of the body. Then rinse thoroughly with clean water.
Care of parts made of artificial materials
Plastic parts, artificial leather seats, headlights, and parts painted matte black can be washed with water with the addition of special detergents. Wetting is not recommended. Plastic parts can be treated with special cleaners if necessary. Under no circumstances should nitro solvent or gasoline be used.
Glass washing
Wipe the glass with a clean soft cloth from the inside and outside. For heavy dirt, use alcohol or ammonia and warm water, special glass cleaners. When washing the windshield, lift the wipers up.
Caution! When using silicone-containing paint cleaners, do not wipe the glass with them. When spraying silicone-containing aerosols, cover the glass with cardboard or other materials.
Caring for rubber seals
Periodically sprinkle sealing or sliding surfaces with talc or spray with silicone aerosol. This will maintain their elasticity and eliminate creaking when closing the doors. You can eliminate unpleasant sounds by wiping the contact surfaces with liquid soap.
Wheel rims
Light alloy wheels require maintenance, especially in the cold season. For this purpose, you can use a special cleaning agent for wheels. Do not use active acid-containing, highly alkaline and rough cleaning agents or water with a temperature above +60°C.
Seat belts
Seat belts should be washed with a mild soap solution without removing them. They should not be dry-cleaned, as this may cause the destruction of the fibers. Belts with automatic winding should be rolled up in a dry state; if necessary, use a special aerosol for better sliding. It is not recommended to dry the belts at temperatures above +80°C or in the open sun.
Fabric coverings
Clean soft seats with a vacuum cleaner or a stiff brush. Clean heavily soiled seats with a soap solution or a special interior cleaning agent. Treat greasy and oily stains with clean gasoline or a stain remover. Do not pour the cleaning agent directly onto the fabric. Remove the stain by rubbing the cleaning agent along the contour from the edge of the stain to the center. Other stains can be removed using a slightly warm soapy solution.
Caution! When using liquid detergents inside the car, try not to over-wet the surface being treated.
The article was taken from the website: mitsubishiman.ru