Car automatic transmission Mitsubishi Space Star

Automatic transmission — technical data
Transmission fluid temperature sensor resistance, kOhm at a temperature of 0°C - 16.7-20.5 at a temperature of 20°C - 7.3-8.9 at a temperature of 40°C - 3.4-4.2 at a...

Diagnostic functions
Automatic transmission selector lever N position lamp If a malfunction occurs in one of the following components that ensure normal operation of the automatic...

Checking the fluid level in the automatic transmission
Warning: If the automatic transmission has been replaced or overhauled or the vehicle has been operated in adverse conditions, the heat exchanger and tubes must be...

Diagnostic codes (F4A42)
Code Malfunction 11 Short circuit in the electrical circuit of the throttle position sensor 12 Open circuit of the throttle position sensor. 14 Throttle Position Sensor...

Automatic transmission fluid replacement
Warning: If the automatic transmission has been replaced or overhauled, or the transmission fluid is contaminated, flush the heat exchanger and transmission fluid cooler...

Flushing transmission fluid cooling heat exchanger tubes
Warning: If the automatic transmission has been replaced or overhauled, or the transmission fluid is contaminated, flush the heat exchanger and transmission fluid cooler...

Replacing the oil filter
1. Using a special tool, unscrew the oil filter (Fig. 13.13). Fig. 13.13. Using a special tool to unscrew the oil filter 2. Wipe the mating surface of the filter...

Checking the selector switch circuits
Disconnect the connector from the selector switch (Fig. 13.15). Fig. 13.15. Selector switch location Check the conductivity between the contacts of the selector switch...

Adjusting the position of the selector switch and gearbox control cable
1. Set the selector lever to position N. 2. On the gearbox side, loosen the nut securing the cable to the control lever to release the cable and control lever (Fig....

Checking the transmission fluid temperature sensor
1. Remove the transmission fluid temperature sensor (Fig. 13.20). Fig. 13.20. Location of the transmission fluid temperature sensor 2. Place the transmission fluid...

Checking the automatic transmission control relay
1. Remove the automatic transmission control relay (Fig. 13.22). Fig. 13.22. Location of the automatic transmission control relay 2. Using jumpers, connect contact 2 of...

Checking the electromagnetic valves
1. Remove the valve block housing cover. 2. Disconnect the connectors from each solenoid valve. 3. Measure the resistance between contacts 1 and 2 of the connector of...

Testing the joint operation of an automatic transmission and engine on a stationary vehicle (stall test)
The test is performed to determine the maximum engine speed when the selector lever is in the D or R positions, and to check the operation of the torque converter and...

Checking the transmission fluid pressure
A transmission fluid pressure test is performed to determine the condition of the hydraulic components and the absence of leaks. 1. Start the engine to warm up the...

Adjusting the pressure in the control system
1. Drain the transmission fluid from the automatic transmission and remove the control valve body cover. 2. The pressure in the downshift clutch line is adjusted using...

Checking the operation of the selector lever
1. Apply the parking brake and check that the selector lever moves easily and smoothly and that it locks in each position. 2. Make sure that the engine starts only when...

Checking the ignition switch locking mechanism
1. Perform the following check. (1) When the brake pedal is fully depressed and the ignition key is in the LOCK (OFF) position or removed from the ignition switch, the...

Checking the selector lever locking mechanism
1. Perform the following check. (1) When the brake pedal is fully depressed and the ignition key is in the ACC position, the selector lever cannot be moved from the P...

Adjusting the gearbox control cable
1. Move the selector lever to position N. 2. Loosen the upper adjusting nut of the selector lever. 3. Check that the ignition switch lock switch is in position N. 4....

Gearbox control cable and selector lever
Removal Remove the floor console. Remove the cotter pin, remove the washer and disconnect the gearbox control cable end from the lever on the gearbox (Fig. 13.36). Fig....

Selector lever and ignition switch locking mechanism
Removal Ignition Switch Lock Cable Remove the floor console. Remove the cotter pin and disconnect the ignition switch lock cable end from the selector lever (Fig. 13.40)...

Removal and installation of automatic transmission
Warning: To prevent damage to the gearbox mounting supports, the connections in the places marked with "*" in Figures 13.41 and 13.43 should be pre-tightened, and the...

Gearbox repair
The gearbox is a very complex unit and its repair must be carried out in a specialized workshop. Also, when removing and installing many parts, it is necessary to...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Similar materials for other Mitsubishi models

➤ Transmission: Automatic gearbox Mitsubishi Colt 4 and 5 (1991-2003)
➤ Transmission: Automatic gearbox Mitsubishi Lancer 9 (2000-2007, petrol)
➤ Transmission: Automatic gearbox Mitsubishi Galant 6 and 7 (1987-1998)
➤ Transmission: Automatic gearbox Mitsubishi Outlander 1 (2003-2008)
➤ Transmission: Automatic gearbox Mitsubishi Pajero 4 (2006-2021)

Share with friends:

Link in different formats to this section

TEXTHTMLBB Code