FBQT diesel engines Mitsubishi Carisma

Specifications and data
Specifications and data

Checking and adjusting the accessory drive belt (cars with air conditioning)
Examination 1. Attach the special tool to the drive belt. 2. Pass the ring gasket of the measuring tool under the graduated scale. Fig. 4.1. Measuring the drive belt...

Checking and adjusting valve clearances
Examination 1. Checking and adjusting valve clearances must be carried out on a cold engine. 2. Remove the cylinder head cover. 3. Check and adjust the valve drive...

Checking and adjusting the fuel injection timing
Examination 1. Turn the crankshaft using the pulley mounting bolt to set the piston of the 1st cylinder to the TDC position in the compression stroke. 2. Turn the...

Checking and adjusting the engine idle speed
Examination 1. Prepare the vehicle for testing (warm up the engine to normal operating coolant temperature). 2. Connect the MUT-II device to the diagnostic connector. 3....

Checking and adjusting the increased engine crankshaft speed at idle during warm-up
1. Disconnect the vacuum hose from the idle speed control actuator. Fig. 4.10. Connecting a hand vacuum pump to the idle speed increase system fitting 2. Connect a hand...

Compression check
1. Pre-check the engine oil, starter and battery. Prepare the car for testing (warm up the engine to normal operating temperature of the coolant). 2. Disconnect the fuel...

Adjusting the timing belt tension of the gas distribution mechanism
1. Remove the timing belt cover. 2. Turn the crankshaft clockwise and set the piston of the 1st cylinder to TDC of the compression stroke. 3. Loosen the timing belt...

Crankshaft pulley — removal and installation
Removal 1. Remove the protective cover. Fig. 4.15. Crankshaft pulley: 1 – front cover of the timing belt; 2 – auxiliary drive belt; 3 – crankshaft pulley 2. Loosen the...

Camshaft and camshaft oil seal
Removal 1. Disconnect the cable from the negative terminal of the battery. 2. Drain the coolant from the engine cooling system. 3. Remove the timing belt. 4. Using a...

Engine oil pan — removal and installation
Removal 1. Disconnect the cable from the negative terminal of the battery. 2. Drain the engine oil from the engine. 3. Remove the engine oil level indicator (dipstick)....

Engine Oil Cooler — Removal and Installation
Removal To remove, follow these steps in sequence. 1. Disconnect the cable from the negative terminal of the battery. 2. Drain the engine oil from the engine. 3. Remove...

Crankshaft seals — removal and installation
Front crankshaft oil seal Removal 1. Remove the timing belt. Fig. 4.23. Crankshaft oil seals: 1 – crankshaft pulley; 2 – key; 3 – front crankshaft oil seal; 4 – rear...

Intermediate shaft seal — removal and installation
Removal 1. Remove the timing belt. Fig. 4.24. Intermediate shaft seal: 1 – intermediate shaft pulley; 2 – bolt, 50 Nm; 3 – crankshaft pulley; 4 – lower rear timing belt...

Cylinder Head Gasket — Removal and Installation
Removal To remove the cylinder head gasket, perform the following operations in sequence. 1. Drain the coolant from the engine cooling system. 2. Remove the inlet hose...

Gas distribution mechanism drive belt
Removal 1. Disconnect the cable from the negative terminal of the battery. 2. Remove the right protective cover. 3. Remove the engine mount bracket. 4. Remove the...

Removal and installation the engine assembly
Removal 1. Disconnect the cable from the negative terminal of the battery. 2. Remove the hood. 3. Drain the coolant from the engine cooling system. 4. Remove the...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share with friends:

Link in different formats to this section

TEXTHTMLBB Code